Mark Stapp [Tue, 30 Jun 2020 16:47:46 +0000 (12:47 -0400)]
zebra: check LSP flags when deleting an LSP
Check the LSP INSTALLED flag in delete apis, to ensure we
enqueue a delete operation for the lfib. Some apis were only
checking the nexthop/nhlfe INSTALLED flags, and those could be
unset if there's an in-flight dataplane update.
Pat Ruddy [Thu, 2 Jul 2020 16:33:37 +0000 (17:33 +0100)]
bgpd: detect change of RT for L3VPN routes
If the RT changes on a L3VPN route then any leak of this route into
a VRF should be withdrawn.
Extend existing EVPN check for RT change to cover L3VPN routes.
Rafael Zalamena [Thu, 2 Jul 2020 17:47:28 +0000 (14:47 -0300)]
topotests: remove duplicated code
Handle the duplicated code with a simple conditional: if called from
specialized API use provided daemons configuration, otherwise fallback
to old `Router` own daemon settings.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Donald Sharp [Tue, 30 Jun 2020 15:16:36 +0000 (11:16 -0400)]
pbrd: Be a bit more lenient with `set nexthop A.B.C.D <intf>`
When specifying an interface in a pbr-map `set nexthop ..` command
be a bit more lenient about the interface.
a) If the interface does not exist bail on the command
(this is the same)
b) If the interface exists but is in a different vrf
than specified use the vrf it is actually in.
(this is new behavior)
Ticket: CM-30187 Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
if we shutdown an interface isisd will delete the adjacencies
on the corresponding circuit, but it will not log the change.
Fix it to make sure that each change is logged. Also specify
the level of the adjacency in the log message, while we are at it.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
Donald Sharp [Wed, 1 Jul 2020 13:00:59 +0000 (09:00 -0400)]
bgpd: peer_af_flag_modify_vty assumes 1 flag at a time
We have a bunch of code in bgp_vty.c that was passing
to peer_af_flag_modify_vty more than 1 flag at a time.
This was causing the underlying routines to get the
flags wrong. In order to prevent this convert all the
places where we send multiple flags down to this function
to individual flag changes.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Donald Sharp [Tue, 30 Jun 2020 19:10:20 +0000 (15:10 -0400)]
tests: pbr is not working properly on arm 4.9 kernels
Just disable pbr tests on anything less than 4.10.
This has to do with the fact that the arm platform
is not allowing us to install a route into a
non default table using a interface associated
with a vrf.
ip route add default 4.5.6.7 via swp39 table 10000
When swp39 is in a vrf other than default
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
attempted to use sorted master lists to do faster lookups
by using a RB Tree. Unfortunately the original code
was creating a list->cmp function *but* never using it.
If you look at the commit, it clearly shows that the
function listnode_add is used to insert but when you
look at that function it is a tail push.
Fixes: #6573
Namely now this ordering is preserved:
bgp as-path access-list originate-only permit ^$
bgp as-path access-list originate-only deny .*
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Donald Sharp [Fri, 26 Jun 2020 11:10:08 +0000 (07:10 -0400)]
tests: Add some more data gathering
From last addition we can tell that the nexthop-group C is
installed but pbr does not think it is. This failure
has been consistent the last 4-5 runs in master. Lets
add a bit more data gathering to figure out what is going on.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Mark Stapp [Thu, 18 Jun 2020 17:26:47 +0000 (13:26 -0400)]
zebra: improve route_entry comparison logic
Improve and centralize some logic used to a) compare two
route_entries, and b) to locate a route_entry that matches
a dplane context object that contains the results of a
fib update. We were not rigorous enough in checking routes'
properties, especially when examining connected routes where
we allow multiple route_entries.
Donald Sharp [Thu, 25 Jun 2020 00:15:12 +0000 (20:15 -0400)]
bgpd: Have bgp ignore SIGHUP at the moment
SIGHUP is ostensibly supposed to reload configuration
from a fresh slate. This is currently horribly broken
so much so that bgp just crashes. I see no point
in trying to make this work considering the yang
work coming down the pike.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Quentin Young [Wed, 24 Jun 2020 20:33:18 +0000 (16:33 -0400)]
alpine: enable multi-arch builds
Now that amd64 dependencies have been removed we can use the correct
architecture specifier for Alpine packaging metadata in order to build
packages for all supported platforms.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Donald Sharp [Wed, 24 Jun 2020 18:30:49 +0000 (14:30 -0400)]
tools: Fix reload with 'ipv6 address...' in interface
When you have this configuration:
int foo
ipv6 address fd01:0:0:1::1/64
And issue a reload statement, FRR-reload
is reducing the code to a
`no ipv6 address fd01:0:0:1::/64`
and then issuing a:
`ipv6 address fd01:0:0:1::/64`
The end result is of course that the foo
interface now has two v6 addresses on it.
The brilliance of this is of course if you
happen to have two systems that are connected
over an interface, and you issue a reload command.
They both get fd01:0:0:1::/64 as an ipv6 address
and DAD detection kicks in and stomps on your stuff.
Put a special hey don't munch the v6 address line
in a reload situation.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Mark Stapp [Wed, 24 Jun 2020 13:27:05 +0000 (09:27 -0400)]
tests: fix interface and debug config diff in topojson framework
Include vrf name with interface name when topojson framework
generates interface configuration. This matches the output of
'show runn', and makes config reset less disruptive. Also
stop removing configured debugs and log output when re-generating
config.
Olivier Dugeon [Tue, 23 Jun 2020 14:31:55 +0000 (16:31 +0200)]
isisd: Segment Routing improve subTLVs parser
For Segment Routing, isis_tlvs.c may failed if incorrect or maformed TLVs
are sent to the FRR router. This patch improve detection of such subTLVs error
and skip them, in particular for SRGB, SRLB and MSD subTLVs.
Olivier Dugeon [Thu, 4 Jun 2020 16:03:04 +0000 (18:03 +0200)]
isisd: Start Label Manager safer
Initial attempt to connect to the Label Manager used an infinite loop with
a sleep statement which block isisd until Label Manager connection fire up.
This commit changes the way Label Manager connection is established and uses
a `thread_add_timer()` call to re-attempt to establish the connection in case
of failure (zebra or label manager not ready).
New variables are added to the SRDB in order to control the request of SRGB
and SRLB to the Label Manager to start Segment Routing in a safe way.
Olivier Dugeon [Wed, 20 May 2020 09:18:31 +0000 (11:18 +0200)]
isisd: Add Segment Routing Local Block support
Segment Routing Local Block (SRLB) is part of RFC8667. This change introduces
the possibility for isisd to advertize SRLB in LSP. Base and Range of SRLB
could be configured through CLI or Yang.
Adjacency-SID are now using this SRLB for label allocation. SRLB could also
be used for SID-Binding (e.g. LDP to SR).
a missing '!' operator was making any STREAM_GETF fail
when in fact it should have succeeded. As a consequence
of this, for example, many link-params of an interface
were not being read and populated.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
Donatas Abraitis [Mon, 22 Jun 2020 13:23:24 +0000 (16:23 +0300)]
bgpd: Do not treat the route as martian for static BGP routes
If we have something like:
```
ip route 1.1.1.0/24 Null0
!
router bgp 100
no bgp ebgp-requires-policy
neighbor 192.168.0.2 remote-as 200
!
address-family ipv4 unicast
network 1.1.1.0/24
redistribute connected
exit-address-family
!
line vty
!
```
1.1.1.0/24 is not advertised due to martian nexthop (0.0.0.0). It starts
working only when we use `redistribute static`.
By checking if it's a BGP static route we able to announce
1.1.1.0/24 with `network 1.1.1.0/24` without redistribute even when
`bgp import-check` is enabled.
Disabling `bgp import-check` works as well, but it's enabled by default
since 7.4.
Mark Stapp [Wed, 17 Jun 2020 14:00:03 +0000 (10:00 -0400)]
ldpd: clean up temp zlog files
Clean up the temp zlog dirs in /var/tmp/frr/ that the ldpd
child processes were leaving. The child processes do a non-
standard lib init/deinit, so they need to explicitly deinit
the zlog module.
build: Allow removal of build configs from version string
A new config option `--disable-version-build-config`
allows you to show short version string by dropping
"configured with:" and all of its build configs
projects / mirror / frr.git / log