Donald Sharp [Mon, 24 Feb 2020 14:08:54 +0000 (09:08 -0500)]
bgpd: Cleanup indentation in bgp_route_refresh_receive
Some code in bgp_route_refresh_receive was spread across several
lines because of an end of line commit. Move comment to a place
to allow better formating.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Tomas Korbar [Thu, 20 Feb 2020 06:37:55 +0000 (07:37 +0100)]
pimd: Make frr able to be built by gcc 10
- Add extern modifier to some declarations in header file and move
qpim_all_pim_routers_addr definition to pimd/pimd.c
`GCC now defaults to -fno-common. As a result, global variable accesses
are more efficient on various targets. In C, global variables with
multiple tentative definitions now result in linker errors.`
Taken from https://gcc.gnu.org/gcc-10/changes.html
Quentin Young [Wed, 19 Feb 2020 21:43:57 +0000 (16:43 -0500)]
zebra: reduce scope of XCALLOC for gr processing
Somewhat gnarly code flow here that might be leaking memory - can't tell
if it's a test artifact or not, but in any case this reduces the
situations in which we need to alloc a block.
And we don't need to check XCALLOC for success...
And we don't need to null check before XFREE...
Or set XFREE'd pointers to NULL...
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Donald Sharp [Wed, 19 Feb 2020 15:52:14 +0000 (10:52 -0500)]
bgpd: Add a better breadcrumb for when bgp is missconfiged
Currently During bgp open collision resolution if both
the router-id's are the same, we correctly follow
the RFC and close the connection. The problem is of course
that there is no notification of the error in configuration
to the end user other than a subtle open debug message.
Explicitly call out the miss-configuration as an error message
as that this miss-config took several hours of debugging to notice.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Mark Stapp [Tue, 18 Feb 2020 19:08:21 +0000 (14:08 -0500)]
doc: correct ip prefix token mapping table
Fix the table that shows the mapping between ip network cli
tokens and the data struct that the cli handler will see.
Optional network/subnet types appear as a pointer to an
all-zeroes struct, not a NULL pointer.
Donald Sharp [Tue, 18 Feb 2020 00:43:22 +0000 (19:43 -0500)]
zebra: Fix checksum calculation to not include old checksum
As part of checksum calculation for a received packet we were
comparing the checksum returned from in_cksum. Typically
when we calculate the checksum the value stored in the checksum
must be all 0's. Store the received checksum and then set
the checksum to 0 and then compare.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
* This commit implements the code style suggestions from Polychaeta.
* This commit also introduces a CLI to toggle the optimization and, a hidden
CLI to display the contents of the constructed prefix tree.
* This commit introduces the building blocks.
A per-route-map prefix tree is introduced.
This tree will consist of the prefixes defined within the prefix-lists
that are added to the match clause of that route-map.
Donald Sharp [Sat, 15 Feb 2020 20:38:48 +0000 (15:38 -0500)]
bgpd: Add a couple more spaces for output on MsgRcvd and MsgSent
annie# show bgp ipv4 uni summ
BGP router identifier 192.168.201.136, local AS number 64539 vrf-id 0
BGP table version 22458946
RIB entries 1458006, using 178 MiB of memory
Peers 4, using 68 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
45.33.5.119 4 0 0 0 0 0 0 never Active
65.19.134.122 4 15096 4611832 108292 0 0 0 6d22h55m 800670
107.13.46.23 4 0 0 0 0 0 0 never Connect
robot(192.168.201.139) 4 64540 1115997511365599 0 0 0 05w2d05h Connect
Total number of neighbors 4
On very busy systems The column output for MsgRcvd and MsgSent can quickly move past 7 columns.
Add a couple more to allow for even display.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Donald Sharp [Sun, 16 Feb 2020 19:14:04 +0000 (14:14 -0500)]
lib: Fix so that `--enable-pcreposix` actually compiles
The `--enable-pcreposix` configure option was not actually compiling
properly. Follow pre-existing pattern for inclusion of regex.h
or the pcreposix.h header.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This is a basic setup and test of evpn-pim.
Create a vxlan device ensure that pim notices this
and setups the appropriate groups and sends them
to the RP.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
1. show ip pim mlag summary
provides MLAG session information and stats
2. show ip pim mlag upstream
displays the upstream entries synced across the MLAG switches
ipmr-lo is an internally added device used for multicast vxlan tunnel
termination. This device is not expected to be managed by the admin
however in the case it is accidentally shut we need to be able handle
it by recovering when it is "no shut" again.
This string is used in some logging for e.g. in zclient_read -
>>>>>>>>>>>>>>>>>>>>>>>>>>
if (zclient_debug)
zlog_debug("zclient 0x%p command %s VRF %u",
(void *)zclient, zserv_command_string(command),
vrf_id);
>>>>>>>>>>>>>>>>>>>>>>>>>>
pimd: remove peerlink_rif from the orig-mroute OIL when it is oper down
In an anycast VTEP setup the peerlink_rif is added as a static OIF
to the originating mroute (bypassing the pim state machine). This is
needed to ensure both MLAG switches rx a copy of encapsulated BUM flow.
We were not handling link state changes on this static OIF resulting
in the wrong vifi being used in the OIL (because of vifi re-allocation).
This commit re-acts to oper state changes by deleting the OIF on link
down and re-adding it on link up.
pimd: stop overloading SRC_IGMP upstream for vxlan local membership
A local membership is created on the vxlan termination device ipmr-lo. This
is done to -
1. Pull multicast vxlan tunnel traffic to the VTEP for termination by
triggering JoinDesired on the BUM multicast group.
2. Include the OIF in the mroute to signal to the dataplane component
that flow needs to be vxlan terminated.
Earlier we were overloading the PIM_UPSTREAM_FLAG_MASK_SRC_IGMP for
this local membership creation but that is creating confusion both in
the state machine and in the show outputs. To avoid that we use the
more apparent PIM_UPSTREAM_FLAG_MASK_SRC_VXLAN_TERM. With this change -
1. We get LHR functionality for VXLAN_TERM mroutes
2. OIF is populated with PIM_OIF_FLAG_PROTO_PIM only
pimd: force update inherited OIL when vxlan local membership is created
When local member is added the (*, G) entry may already be in a JOINED
state. In that case the OIL is not updated i.e. pim_channel_add_oif is
not happening for ipmr-lo. Because of this the traffic associated with
the multicast vxlan tunnel is pulled down to the VTEP but not terminated
by the kernel.
This change force updates the OIL anytime ipmr-lo is added or removed
as a local member.
pimd: increase RPF metric via the peerlink_rif by plus-10
The RPF cost is incremented by 10 if the RPF interface is the peerlink-rif.
This is used to force the MLAG switch with the lowest cost to the RPF
to become the MLAG DF. If a switch has to go via the peerlink-rif to get
to the RP or source it simplly cannot be the designated forwarder.
pimd: inherit MLAG DF role from the parent (*, G) entry
DF election is only run for (*,G) entries i.e. election is skipped
for (S,G) entries that are setup as a result of SPT switchover. (S,G)
entries inherit the DF role from the parent (*,G) entry. So the DF is
responsible for terminating all sources associated with a group.
pim: DF election for tunnel termination mroutes in an anycast-VTEP setup
1. Upstream entries associated with tunnel termination mroutes are
synced to the MLAG peer via the local MLAG daemon.
2. These entries are installed in the peer switch (via an upstream
ref flag).
3. DF (Designated Forwarder) election is run per-upstream entry by both
the MLAG switches -
a. The switch with the lowest RPF cost is the DF winner
b. If both switches have the same RPF cost the MLAG role is
used as a tie breaker with the MLAG primary becoming the DF
winner.
4. The DF winner terminates the multicast traffic by adding the tunnel
termination device to the OIL. The non-DF suppresses the termination
device from the OIL.
Note: Before the PIM-MLAG interface was available hidden config was
used to test the EVPN-PIM functionality with MLAG. I have removed the
code to persist that config to avoid confusion. The hidden commands are
still available.
Channel with the MLAG daemon is setup on the first VxLAN BUM MDT or
pim-mlag AA SVI.
This channel is used for -
1. rxing MLAG status status updates (peer state, role etc.)
2. for syncing active-active upstream entries with the peer MLAG
switch.
Don Slice [Mon, 10 Feb 2020 18:58:41 +0000 (18:58 +0000)]
zebra: add all ipv6 global addresses to RA messages
RFC 4861 states that ipv6 RA messages sent out an interface should
contain all global ipv6 addresses on that interface. This fix adds
that capability. To override the default flags and timer settings
for a particular prefix, the existing "ipv6 nd prefix ..." command
should be used via vtysh under the appropriate interface.
Ticket: CM-20363 Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
projects / mirror / frr.git / log