Iggy Frankovic [Thu, 30 May 2024 11:59:54 +0000 (07:59 -0400)]
ospf6d: Prevent heap-buffer-overflow with unknown type
When parsing a osf6 grace lsa field and we receive an
unknown tlv type, ospf6d was not incrementing the pointer
to get beyond the tlv. Leaving a situation where ospf6d
would parse the packet incorrectly.
Donatas Abraitis [Tue, 13 Jun 2023 13:08:24 +0000 (16:08 +0300)]
bgpd: Use enum bgp_create_error_code as argument in header
```
bgpd/bgp_vty.c:865:5: warning: conflicting types for ‘bgp_vty_return’ due to enum/integer mismatch; have ‘int(struct vty *, enum bgp_create_error_code)’ [-Wenum-int-mismatch]
865 | int bgp_vty_return(struct vty *vty, enum bgp_create_error_code ret)
| ^~~~~~~~~~~~~~
In file included from ./bgpd/bgp_mplsvpn.h:15,
from bgpd/bgp_vty.c:48:
./bgpd/bgp_vty.h:148:12: note: previous declaration of ‘bgp_vty_return’ with type ‘int(struct vty *, int)’
148 | extern int bgp_vty_return(struct vty *vty, int ret);
| ^~~~~~~~~~~~~~
```
Donatas Abraitis [Tue, 13 Jun 2023 13:01:40 +0000 (16:01 +0300)]
bgpd: Use enum bgp_fsm_state_progress for bgp_stop()
```
bgpd/bgp_fsm.c:1360:29: warning: conflicting types for ‘bgp_stop’ due to enum/integer mismatch; have ‘enum bgp_fsm_state_progress(struct peer *)’ [-Wenum-int-mismatch]
1360 | enum bgp_fsm_state_progress bgp_stop(struct peer *peer)
| ^~~~~~~~
In file included from bgpd/bgp_fsm.c:29:
./bgpd/bgp_fsm.h:111:12: note: previous declaration of ‘bgp_stop’ with type ‘int(struct peer *)’
111 | extern int bgp_stop(struct peer *peer);
| ^~~~~~~~
```
Acee [Tue, 28 May 2024 14:02:27 +0000 (10:02 -0400)]
ospf6d: OSPFv3 route change comparision fixed for ASBR-only change
When a router route already exists in the area border routers table
as an ABR and it solely changes its ABR or ASBR status, the change
was missed and border route is not updated. This fixes the comparison
for the router_bits in the ospf6_path structure.
This fixes issue https://github.com/FRRouting/frr/issues/16053 although
the actual problem is not the computing router (r2) and not the OSPFv3
redistribution (r3).
During fuzzing, Iggy Frankovic discovered that get_edge() function in ospf_te.c
could return null pointer, in particular when the link_id or advertised router
IP addresses are fuzzed. As the null pointer returned by get_edge() function is
not handlei by calling functions, this could cause ospfd crash.
This patch introduces new verification of returned pointer by get_edge()
function and stop the processing in case of null pointer. In addition, link ID
and advertiser router ID are validated before calling ls_find_edge_by_key() to
avoid the creation of a new edge with an invalid key.
Iggy Frankovic discovered another ospfd crash when performing fuzzing of OSPF
LSA packets. The crash occurs in ospf_te_parse_ext_link() function when
attemping to read Segment Routing Adjacency SID subTLVs. The original code
doesn't check if the size of the Extended Link TLVs and subTLVs have the correct
length. In presence of erronous LSA, this will cause a buffer overflow and ospfd
crashes.
This patch introduces new verification of the subTLVs size for Extended Link
TLVs and subTLVs. Similar check has been also introduced for the Extended
Prefix TLV.
Iggy Frankovic discovered another ospfd crash when performing fuzzing of OSPF
LSA packets. The crash occurs in ospf_te_parse_ri() function when attemping to
read Segment Routing subTLVs. The original code doesn't check if the size of
the SR subTLVs have the correct length. In presence of erronous LSA, this will
cause a buffer overflow and ospfd crash.
This patch introduces new verification of the subTLVs size for Router
Information TLV.
Louis Scalbert [Thu, 16 May 2024 14:44:03 +0000 (16:44 +0200)]
isisd: fix heap-after-free with prefix sid
> ==2334217==ERROR: AddressSanitizer: heap-use-after-free on address 0x61000001d0a0 at pc 0x563828c8de6f bp 0x7fffbdaee560 sp 0x7fffbdaee558
> READ of size 1 at 0x61000001d0a0 thread T0
> #0 0x563828c8de6e in prefix_sid_cmp isisd/isis_spf.c:187
> #1 0x7f84b8204f71 in hash_get lib/hash.c:142
> #2 0x7f84b82055ec in hash_lookup lib/hash.c:184
> #3 0x563828c8e185 in isis_spf_prefix_sid_lookup isisd/isis_spf.c:209
> #4 0x563828c90642 in isis_spf_add2tent isisd/isis_spf.c:598
> #5 0x563828c91cd0 in process_N isisd/isis_spf.c:824
> #6 0x563828c93852 in isis_spf_process_lsp isisd/isis_spf.c:1041
> #7 0x563828c98dde in isis_spf_loop isisd/isis_spf.c:1821
> #8 0x563828c998de in isis_run_spf isisd/isis_spf.c:1983
> #9 0x563828c99c7b in isis_run_spf_with_protection isisd/isis_spf.c:2009
> #10 0x563828c9a60d in isis_run_spf_cb isisd/isis_spf.c:2090
> #11 0x7f84b835c72d in event_call lib/event.c:2011
> #12 0x7f84b8236d93 in frr_run lib/libfrr.c:1217
> #13 0x563828c21918 in main isisd/isis_main.c:346
> #14 0x7f84b7e4fd09 in __libc_start_main ../csu/libc-start.c:308
> #15 0x563828c20df9 in _start (/usr/lib/frr/isisd+0xf5df9)
>
> 0x61000001d0a0 is located 96 bytes inside of 184-byte region [0x61000001d040,0x61000001d0f8)
> freed by thread T0 here:
> #0 0x7f84b88a9b6f in __interceptor_free ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:123
> #1 0x7f84b8263bae in qfree lib/memory.c:130
> #2 0x563828c8e433 in isis_vertex_del isisd/isis_spf.c:249
> #3 0x563828c91c95 in process_N isisd/isis_spf.c:811
> #4 0x563828c93852 in isis_spf_process_lsp isisd/isis_spf.c:1041
> #5 0x563828c98dde in isis_spf_loop isisd/isis_spf.c:1821
> #6 0x563828c998de in isis_run_spf isisd/isis_spf.c:1983
> #7 0x563828c99c7b in isis_run_spf_with_protection isisd/isis_spf.c:2009
> #8 0x563828c9a60d in isis_run_spf_cb isisd/isis_spf.c:2090
> #9 0x7f84b835c72d in event_call lib/event.c:2011
> #10 0x7f84b8236d93 in frr_run lib/libfrr.c:1217
> #11 0x563828c21918 in main isisd/isis_main.c:346
> #12 0x7f84b7e4fd09 in __libc_start_main ../csu/libc-start.c:308
>
> previously allocated by thread T0 here:
> #0 0x7f84b88aa037 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154
> #1 0x7f84b8263a6c in qcalloc lib/memory.c:105
> #2 0x563828c8e262 in isis_vertex_new isisd/isis_spf.c:225
> #3 0x563828c904db in isis_spf_add2tent isisd/isis_spf.c:588
> #4 0x563828c91cd0 in process_N isisd/isis_spf.c:824
> #5 0x563828c93852 in isis_spf_process_lsp isisd/isis_spf.c:1041
> #6 0x563828c98dde in isis_spf_loop isisd/isis_spf.c:1821
> #7 0x563828c998de in isis_run_spf isisd/isis_spf.c:1983
> #8 0x563828c99c7b in isis_run_spf_with_protection isisd/isis_spf.c:2009
> #9 0x563828c9a60d in isis_run_spf_cb isisd/isis_spf.c:2090
> #10 0x7f84b835c72d in event_call lib/event.c:2011
> #11 0x7f84b8236d93 in frr_run lib/libfrr.c:1217
> #12 0x563828c21918 in main isisd/isis_main.c:346
> #13 0x7f84b7e4fd09 in __libc_start_main ../csu/libc-start.c:308
>
> SUMMARY: AddressSanitizer: heap-use-after-free isisd/isis_spf.c:187 in prefix_sid_cmp
> Shadow bytes around the buggy address:
> 0x0c207fffb9c0: fa fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
> 0x0c207fffb9d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fa
> 0x0c207fffb9e0: fa fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
> 0x0c207fffb9f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fa
> 0x0c207fffba00: fa fa fa fa fa fa fa fa fd fd fd fd fd fd fd fd
> =>0x0c207fffba10: fd fd fd fd[fd]fd fd fd fd fd fd fd fd fd fd fa
> 0x0c207fffba20: fa fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
> 0x0c207fffba30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fa
> 0x0c207fffba40: fa fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
> 0x0c207fffba50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fa
> 0x0c207fffba60: fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa fa
> Shadow byte legend (one shadow byte represents 8 application bytes):
> Addressable: 00
> Partially addressable: 01 02 03 04 05 06 07
> Heap left redzone: fa
> Freed heap region: fd
> Stack left redzone: f1
> Stack mid redzone: f2
> Stack right redzone: f3
> Stack after return: f5
> Stack use after scope: f8
> Global redzone: f9
> Global init order: f6
> Poisoned by user: f7
> Container overflow: fc
> Array cookie: ac
> Intra object redzone: bb
> ASan internal: fe
> Left alloca redzone: ca
> Right alloca redzone: cb
> Shadow gap: cc
> ==2334217==ABORTING
Fixes: 2f7cc7bcd3 ("isisd: detect Prefix-SID collisions and handle them appropriately") Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
(cherry picked from commit e697de58431474cdb06eff79bcbc70de4215e222)
zebra: Deny the routes if ip protocol CLI refers to an undefined rmap
Currently zebra does not deny the routes if `ip protocol <proto> route-map
FOO`
commmand is configured with reference to an undefined route-map (FOO in
this case).
However, on FRR restart, in zebra_route_map_check() routes get denied
if route-map name is available but the route-map is not defined. This
change was introduced in fd303a4ba14c762550db972317e1e88528768005.
Fix:
When `ip protocol <proto> route-map FOO` CLI is configured with reference to an
undefined route-map FOO, let the processing in ip_protocol_rm_add() and
ip_protocol_rm_del() go through so that zebra can deny the routes instead
of simply returning. This will result in consistent behavior.
Testing Done:
Before fix:
```
spine-1# configure
spine-1(config)# ip protocol bgp route-map rmap7
spine-1(config)# do show ip route
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, A - Babel, D - SHARP, F - PBR, f - OpenFabric,
Z - FRR,
> - selected route, * - FIB route, q - queued, r - rejected, b - backup
t - trapped, o - offload failure
C>* 27.0.0.1/32 is directly connected, lo, 02:27:45
B>* 27.0.0.3/32 [20/0] via fe80::202:ff:fe00:21, downlink_1, weight 1, 02:27:35
B>* 27.0.0.4/32 [20/0] via fe80::202:ff:fe00:29, downlink_2, weight 1, 02:27:40
B>* 27.0.0.5/32 [20/0] via fe80::202:ff:fe00:31, downlink_3, weight 1, 02:27:40
B>* 27.0.0.6/32 [20/0] via fe80::202:ff:fe00:39, downlink_4, weight 1, 02:27:40
```
After fix:
```
spine-1(config)# ip protocol bgp route-map route-map67
spine-1(config)# do show ip route
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, A - Babel, D - SHARP, F - PBR, f - OpenFabric,
Z - FRR,
> - selected route, * - FIB route, q - queued, r - rejected, b - backup
t - trapped, o - offload failure
C>* 27.0.0.1/32 is directly connected, lo, 00:35:03
B 27.0.0.3/32 [20/0] via fe80::202:ff:fe00:21, downlink_1 inactive, weight 1, 00:34:58
B 27.0.0.4/32 [20/0] via fe80::202:ff:fe00:29, downlink_2 inactive, weight 1, 00:34:57
B 27.0.0.5/32 [20/0] via fe80::202:ff:fe00:31, downlink_3 inactive, weight 1, 00:34:57
B 27.0.0.6/32 [20/0] via fe80::202:ff:fe00:39, downlink_4 inactive, weight 1, 00:34:58
spine-1(config)#
root@spine-1:mgmt:/var/home/cumulus# ip route show
root@spine-1:mgmt:/var/home/cumulus#
```
Igor Ryzhov [Mon, 1 Apr 2024 21:56:17 +0000 (00:56 +0300)]
isisd: fix ip/ipv6 reachability tlvs
Don't allocate subtlvs container if there's nothing to add to it. If the
container is allocated, the "sub-TLVs presence" bit is set in the TLVs
even if there's no actual sub-TLVs, what violates the RFC.
David Lamparter [Mon, 12 Dec 2022 16:50:59 +0000 (17:50 +0100)]
pimd: fix order of operations for evaluating join
join_desired looks at whether up->channel_oil is empty. up->channel_oil
is updated from pim_forward_stop(), calling pim_channel_del_oif(). But
that was being called *after* updating join_desired, so join_desired saw
a non-empty OIL. Pull up the pim_forward_stop() call to before updating
join_desired.
David Lamparter [Mon, 17 Apr 2023 09:47:08 +0000 (11:47 +0200)]
pimd: fix null register before aging out reg-stop
It looks like the code was trying to do this with the null_register
parameter on pim_upstream_start_register_stop_timer(), but that didn't
quite work right. Restructure a bit to get it right.
pimd crashs while unconfigure of rp ka timer as we are trying to access
a yand dnode(suppress timer) which does not exist at the moment.
User just configured rp keepalive timer and not suppress timer,
the yang dnode would not be present. Instead of directly accessing
yang_dnode_get_unit16, first check the yang node exist using
the xpath.
Before:
------
tor-11(config)# no ip pim rp keep-alive-timer 3000
vtysh: error reading from pimd: Success (0)Warning: closing connection to pimd because of an I/O error!
Broadcast message from root@tor-11 (somewhere) (Mon Apr 22 17:29:12 2024):
cumulus-core: Running cl-support for core files "pimd.25467.1713806952.core"
After:
-----
tor-11(config)# no ip pim rp keep-alive-timer 3000
tor-11(config)#
Signed-off-by: Donald Sharp <sharpd@nvidia.com> Signed-off-by: Vijayalaxmi Basavaraj <vbasavaraj@nvidia.com>
(cherry picked from commit 0c4b7c1f1f359c1d7647fea34f62378af8b640a5)
Donald Sharp [Fri, 19 Apr 2024 16:13:32 +0000 (12:13 -0400)]
lib, zebra: Check for not being a blackhole route
In zebra_interface_nhg_reinstall zebra is checking that the
nhg is a singleton and not a blackhole nhg. This was originally
done with checking that the nexthop is a NEXTHOP_TYPE_IFINDEX,
NEXTHOP_TYPE_IPV4_IFINDEX and NEXTHOP_TYPE_IPV6_IFINDEX. This
was excluding NEXTHOP_TYPE_IPV4 and NEXTHOP_TYPE_IPV6. These
were both possible to be received and maintained from the upper
level protocol for when a route is being recursively resolved.
If we have gotten to this point in zebra_interface_nhg_reinstall
the nexthop group has already been installed at least once
and we *know* that it is actually a valid nexthop. What the
test is really trying to do is ensure that we are not reinstalling
a blackhole nexthop group( Which is not possible to even be
here by the way, but safety first! ). So let's change
to test for that instead.
Donald Sharp [Thu, 11 Apr 2024 14:46:46 +0000 (10:46 -0400)]
bgpd: Fix display when using `missing-as-worst`
The usage of the `bgp bestpath med missing-as-worst` command
was being accepted and applied during bestpath, but during output
of the routes affected by this it would not give any indication
that this was happening or what med value was being used.
Donald Sharp [Thu, 28 Mar 2024 16:27:38 +0000 (12:27 -0400)]
bgpd: Arrange peer notification to after zebra announce
Currently BGP attempts to send route change information
to it's peers *before* the route is installed into zebra.
This creates a bug in suppress-fib-pending in the following
scenario:
a) bgp suppress-fib-pending and bgp has a route with
2 way ecmp.
b) bgp receives a route withdraw from peer 1. BGP
will send the route to zebra and mark the route as
FIB_INSTALL_PENDING.
c) bgp receives a route withdraw from peer 2. BGP
will see the route has the FIB_INSTALL_PENDING and
not send the withdrawal of the route to the peer.
bgp will then send the route deletion to zebra and
clean up the bgp_path_info's.
At this point BGP is stuck where it has not sent
a route withdrawal to downstream peers.
Let's modify the code in bgp_process_main_one to
send the route notification to zebra first before
attempting to announce the route. The route withdrawal
will remove the FIB_INSTALL_PENDING flag from the dest
and this will allow group_announce_route to believe
it can send the route withdrawal.
For the master branch this is ok because the recent
backpressure commits are in place and nothing is going
to change from an ordering perspective in that regards.
Ostensibly this fix is also for operators of Sonic and
will be backported to the 8.5 branch as well. This will
change the order of the send to peers to be after the
zebra installation but sonic users are using suppress-fib-pending
anyways so updates won't go out until rib ack has been
received anyways.
Donald Sharp [Thu, 28 Mar 2024 16:25:05 +0000 (12:25 -0400)]
bgpd: Note when receiving but not understanding a route notification
When BGP has been asked to wait for FIB installation, on route
removal a return call is likely to not have the dest since BGP
will have cleaned up the node, entirely. Let's just note that
the prefix cannot be found if debugs are turned on and move on.
Donatas Abraitis [Wed, 27 Mar 2024 17:08:38 +0000 (19:08 +0200)]
bgpd: Prevent from one more CVE triggering this place
If we receive an attribute that is handled by bgp_attr_malformed(), use
treat-as-withdraw behavior for unknown (or missing to add - if new) attributes.
Donatas Abraitis [Wed, 27 Mar 2024 16:42:56 +0000 (18:42 +0200)]
bgpd: Fix error handling when receiving BGP Prefix SID attribute
Without this patch, we always set the BGP Prefix SID attribute flag without
checking if it's malformed or not. RFC8669 says that this attribute MUST be discarded.
Also, this fixes the bgpd crash when a malformed Prefix SID attribute is received,
with malformed transitive flags and/or TLVs.
Philippe Guibert [Fri, 29 Mar 2024 07:35:34 +0000 (08:35 +0100)]
bgpd: fix srv6 memory leak detection
The asan memory leak has been detected:
> Direct leak of 16 byte(s) in 1 object(s) allocated from:
> #0 0x7f9066dadd28 in __interceptor_calloc (/usr/lib/x86_64-linux-gnu/libasan.so.4+0xded28)
> #1 0x7f9066779b5d in qcalloc lib/memory.c:105
> #2 0x556d6ca527c2 in vpn_leak_zebra_vrf_sid_update_per_af bgpd/bgp_mplsvpn.c:389
> #3 0x556d6ca530e1 in vpn_leak_zebra_vrf_sid_update bgpd/bgp_mplsvpn.c:451
> #4 0x556d6ca64b3b in vpn_leak_postchange bgpd/bgp_mplsvpn.h:311
> #5 0x556d6ca64b3b in vpn_leak_postchange_all bgpd/bgp_mplsvpn.c:3751
> #6 0x556d6cb9f116 in bgp_zebra_process_srv6_locator_chunk bgpd/bgp_zebra.c:3337
> #7 0x7f906685a6b6 in zclient_read lib/zclient.c:4490
> #8 0x7f9066826a32 in event_call lib/event.c:2011
> #9 0x7f906675c444 in frr_run lib/libfrr.c:1217
> #10 0x556d6c980d52 in main bgpd/bgp_main.c:545
> #11 0x7f9065784c86 in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x21c86)
Fix this by freeing the previous memory chunk.
Fixes: b72c9e14756f ("bgpd: cli for SRv6 SID alloc to redirect to vrf (step4)") Fixes: 527588aa78b2 ("bgpd: add support for per-VRF SRv6 SID") Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
(cherry picked from commit eea8a8ae248ed726449878c7a74705d779469fda)
Donald Sharp [Fri, 6 Oct 2023 16:48:38 +0000 (12:48 -0400)]
bgpd: Convert the bgp_advertise_attr->adv to a fifo
BGP is storing outgoing updates in a couple of different
fifo's. This is to ensure proper packet packing of
all bgp_dests that happen to use the same attribute.
How it's all put together currently: On initial update
BGP walks through all the bgp_dest's in a table. For each
path being sent a bgp_advertise is created. This bgp_advertise
is placed in fifo order on the bgp_synchronize->update queue.
The bgp_advertise has a pointer to the bgp_advertise_attr which
is associated iwth the actual attribute that is being sent to
it's peer. In turn this bgp_advertise is placed in a fifo off
of the bgp_advertise_attr structure. As such as we have paths
that share an attribute, the path/dest is placed on the
bgp_syncrhonize->update fifo as well as being placed on the fifo
associated with the advertised attribute.
On actual creation of a packet. The first item in the
bgp_synchronize->update fifo is popped. The bgp_advertise_attr
pointer is grabbed, we fill out the nlri part of the bgp packet
and then walk the bgp_advertise_attr fifo to place paths/dests in
the packet. As each path/dest is placed in the packet it is removed
from both the bgp_synchronize->update fifo and the bgp_advertise_attr
fifo.
The whole point of this change is to switch the *next, *prev
pointers in the bgp_advertise structure with a typesafe data
structure.
Tomi Salminen [Wed, 13 Dec 2023 09:37:21 +0000 (11:37 +0200)]
zebra: Fix crash on macvlan link down/up
Whenever a link up change was detected on a macvlan device where
the linked device wasn't visible in the namespace zebra was
running in, the linked zebra interface was NULL. This was already
handled in the event of a link down, but was ommitted from the
upside. Added the same null check to the up-side.
Donatas Abraitis [Fri, 15 Mar 2024 11:49:06 +0000 (13:49 +0200)]
bgpd: Update default-originate route-map actual map structure
If using with `bgp listen range ... peer-group x`, default_rmap[afi][safi] is not
updated, and after the hard-reset in other side, this is flushed and never updated
again without restarting the sender BGP daemon.
Donald Sharp [Sat, 2 Mar 2024 14:50:38 +0000 (09:50 -0500)]
bgpd: Ensure community data is freed in some cases.
Customer has this valgrind trace:
Direct leak of 2829120 byte(s) in 70728 object(s) allocated from:
0 in community_new ../bgpd/bgp_community.c:39
1 in community_uniq_sort ../bgpd/bgp_community.c:170
2 in route_set_community ../bgpd/bgp_routemap.c:2342
3 in route_map_apply_ext ../lib/routemap.c:2673
4 in subgroup_announce_check ../bgpd/bgp_route.c:2367
5 in subgroup_process_announce_selected ../bgpd/bgp_route.c:2914
6 in group_announce_route_walkcb ../bgpd/bgp_updgrp_adv.c:199
7 in hash_walk ../lib/hash.c:285
8 in update_group_af_walk ../bgpd/bgp_updgrp.c:2061
9 in group_announce_route ../bgpd/bgp_updgrp_adv.c:1059
10 in bgp_process_main_one ../bgpd/bgp_route.c:3221
11 in bgp_process_wq ../bgpd/bgp_route.c:3221
12 in work_queue_run ../lib/workqueue.c:282
The above leak detected by valgrind was from a screenshot so I copied it
by hand. Any mistakes in line numbers are purely from my transcription.
Additionally this is against a slightly modified 8.5.1 version of FRR.
Code inspection of 8.5.1 -vs- latest master shows the same problem
exists. Code should be able to be followed from there to here.
What is happening:
There is a route-map being applied that modifes the outgoing community
to a peer. This is saved in the attr copy created in
subgroup_process_announce_selected. This community pointer is not
interned. So the community->refcount is still 0. Normally when
a prefix is announced, the attr and the prefix are placed on a
adjency out structure where the attribute is interned. This will
cause the community to be saved in the community hash list as well.
In a non-normal operation when the decision to send is aborted after
the route-map application, the attribute is just dropped and the
pointer to the community is just dropped too, leading to situations
where the memory is leaked. The usage of bgp suppress-fib would
would be a case where the community is caused to be leaked.
Additionally the previous commit where an unsuppress-map is used
to modify the outgoing attribute but since unsuppress-map was
not considered part of outgoing policy the attribute would be dropped as
well. This pointer drop also extends to any dynamically allocated
memory saved by the attribute pointer that was not interned yet as well.
So let's modify the return case where the decision is made to
not send the prefix to the peer to always just flush the attribute
to ensure memory is not leaked.
Fixes: #15459 Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Donald Sharp [Wed, 13 Mar 2024 14:26:58 +0000 (10:26 -0400)]
bgpd: Ensure that the correct aspath is free'd
Currently in subgroup_default_originate the attr.aspath
is set in bgp_attr_default_set, which hashs the aspath
and creates a refcount for it. If this is a withdraw
the subgroup_announce_check and bgp_adj_out_set_subgroup
is called which will intern the attribute. This will
cause the the attr.aspath to be set to a new value
finally at the bottom of the function it intentionally
uninterns the aspath which is not the one that was
created for this function. This reduces the other
aspath's refcount by 1 and if a clear bgp * is issued
fast enough the aspath for that will be removed
and the system will crash.
Louis Scalbert [Tue, 20 Feb 2024 16:49:01 +0000 (17:49 +0100)]
zebra: fix crash if macvlan link in another netns
A macvlan interface can have its underlying link-interface in another
namespace (aka. netns). However, by default, zebra does not know the
interface from the other namespaces. It results in a crash the pointer
to the link interface is NULL.
Fix the crash by returning when the macvlan link-interface is in another
namespace. No need to go further because any vxlan under the macvlan
interface would not be accessible by zebra.
Olivier Dugeon [Mon, 26 Feb 2024 09:40:34 +0000 (10:40 +0100)]
ospfd: Solved crash in OSPF TE parsing
Iggy Frankovic discovered an ospfd crash when perfomring fuzzing of OSPF LSA
packets. The crash occurs in ospf_te_parse_te() function when attemping to
create corresponding egde from TE Link parameters. If there is no local
address, an edge is created but without any attributes. During parsing, the
function try to access to this attribute fields which has not been created
causing an ospfd crash.
The patch simply check if the te parser has found a valid local address. If not
found, we stop the parser which avoid the crash.
zebra: fix nhg out of sync between zebra and kernel
PR#13413 introduces reinstall mechanism, but there is problem with the route
leak scenario.
With route leak configuration: ( `x1` and `x2` are binded to `vrf1` )
```
vrf vrf2
ip route 75.75.75.75/32 77.75.1.75 nexthop-vrf vrf1
ip route 75.75.75.75/32 77.75.2.75 nexthop-vrf vrf1
exit-vrf
```
Firstly, all are ok. But after `x1` is set down and up ( The interval
between the down and up operations should be less than 180 seconds. ) ,
`x1` is lost from the nexthop group:
```
anlan# ip nexthop
id 121 group 122/123 proto zebra
id 122 via 77.75.1.75 dev x1 scope link proto zebra
id 123 via 77.75.2.75 dev x2 scope link proto zebra
anlan# ip route show table 2
75.75.75.75 nhid 121 proto 196 metric 20
nexthop via 77.75.1.75 dev x1 weight 1
nexthop via 77.75.2.75 dev x2 weight 1
anlan# ip link set dev x1 down
anlan# ip link set dev x1 up
anlan# ip route show table 2 <- Wrong, one nexthop lost from group
75.75.75.75 nhid 121 via 77.75.2.75 dev x2 proto 196 metric 20
anlan# ip nexthop
id 121 group 123 proto zebra
id 122 via 77.75.1.75 dev x1 scope link proto zebra
id 123 via 77.75.2.75 dev x2 scope link proto zebra
anlan# show ip route vrf vrf2 <- Still ok
VRF vrf2:
S>* 75.75.75.75/32 [1/0] via 77.75.1.75, x1 (vrf vrf1), weight 1, 00:00:05
* via 77.75.2.75, x2 (vrf vrf1), weight 1, 00:00:05
```
From the impact on kernel:
The `nh->type` of `id 122` is *always* `NEXTHOP_TYPE_IPV4` in the route leak
case. Then, `nexthop_is_ifindex_type()` introduced by commit `5bb877` always
returns `false`, so its dependents can't be reinstalled. After `x1` is down,
there is only `id 123` in the group of `id 121`. So, Finally `id 121` remains
unchanged after `x1` is up, i.e., `id 122` is not added to the group even it is
reinstalled itself.
From the impact on zebra:
The `show ip route vrf vrf2` is still ok because the `id`s are reused/reinstalled
successfully within 180 seconds after `x1` is down and up. The group of `id 121`
is with old `NEXTHOP_GROUP_INSTALLED` flag, and it is still the group of `id 122`
and `id 123` as before.
In this way, kernel and zebra have become out of sync.
The `nh->type` of `id 122` should be adjusted to `NEXTHOP_TYPE_IPV4_IFINDEX`
after nexthop resolved. This commit is for doing this to make that reinstall
mechanism work.
pimd: re-evaluated S,G OILs upon RP changes and for empty SG upstream oils
Topology:
TOR11 (FHR) --- LEAF-11---SPINE1 (RP)MSDP SPINE-2(RP)MSDP --- LEAF-12 -- TOR12 (LHR)
| | | | |
| -----------------------------------------------------(ECMP) |
| | | |
-----------------------------------------------------------------------(ECMP)
Issue:
In some triggers, S,G upstream is preserved even with the PP timer expiry, resulting
in S,G with NULL OILS. This could be because we create a dummy S,G upstream and
dummy channel_oif for *,G, where RPF is UNKNOWN. As a result, PIM+VXLAN traffic is never
forwarded downstream to LHR.
Fix:
when the S,G stream is running, Determine if a reevaluation of the outgoing interface
list (OIL) is required. S,G upstream should then inherit the OIL from *,G.
ospfd: can not delete "segment-routing node-msd" when SR if off
This fixes the initial implementation of commit 7743f2f8c00 ("OSPFd: Update
Segment Routing PR following review") where it wsa not possible to remove
the "segment-routing node-msd" CLI nodes via vtysh once segment-routing got
disabled.
Chirag Shah [Sat, 8 Jul 2023 20:17:12 +0000 (13:17 -0700)]
tools: fix ospf area stub summary in frr-reload
OSPFv2 no area x stub no-summary only resets
'no-summary' config. From frr-reload if the config
line 'area x stub no-summary' is removed then
it needs to remove completely. Before this change
it took two frr-roload to remove the config which is
inconsistent behavior.
Fix is to frr-reload to add extra line to delete
'no area x stub'.
router ospf
ospf router-id 6.6.6.6
area 0.0.0.1 stub no-summary
area 0.0.0.2 stub
exit
!
router ospf vrf sym_1
area 0.0.1.1 range 24.1.1.0/24
area 0.0.1.2 stub no-summary
exit
changed frr.conf:
router ospf
ospf router-id 6.6.6.6
area 0.0.0.2 stub
exit
!
router ospf vrf sym_1
area 0.0.1.1 range 24.1.1.0/24
exit
Lines To Delete
===============
router ospf
no area 0.0.0.1 stub <<<< newly added
router ospf vrf sym_1
no area 0.0.1.2 stub <<<< newly added
router ospf
no area 0.0.0.1 stub no-summary
router ospf vrf sym_1
no area 0.0.1.2 stub no-summary
After fix new running-config post reload:
i
router ospf
ospf router-id 6.6.6.6
area 0.0.0.2 stub
exit
!
router ospf vrf sym_1
area 0.0.1.1 range 24.1.1.0/24
exit
Before fix running-config post 1st reload:
router ospf
ospf router-id 6.6.6.6
area 0.0.0.1 stub
area 0.0.0.2 stub
exit
!
router ospf vrf sym_1
area 0.0.1.1 range 24.1.1.0/24
area 0.0.1.2 stub
exit
Chirag Shah [Thu, 29 Jun 2023 16:55:12 +0000 (09:55 -0700)]
tools: fix pim interface config deletion
When no ip pim is performed subsequent pim related
configs under the interface also implicitly deleted.
When doing this via frr-reload requires to remove any
explicit no ip pim <blah> lines so delete list.
Testing Done:
running-config:
interface lo
ip pim
ip pim use-source 6.0.0.1
exit
frr.conf:
remove two pim config lines.
interface lo
exit
Before fix:
2023-06-29 23:44:26,062 INFO: Failed to execute interface lo no ip pim use-source 6.0.0.1
2023-06-29 23:44:26,142 INFO: Failed to execute interface lo no ip pim use-source
2023-06-29 23:44:26,221 INFO: Executed "interface lo no ip pim"
After fix:
Only no ip pim executed and rest of the other lines removed from delete
list.
2023-06-30 01:07:32,618 INFO: Executed "interface lo no ip pim"
Igor Ryzhov [Sun, 28 Nov 2021 21:36:35 +0000 (00:36 +0300)]
tools: always append "exit" in frr-reload.py
When reloading the following config:
```
router ospf6
area 0 range 2001:db8::/32 advertise
exit
!
interface eth0
ipv6 ospf6 area 0
exit
```
frr-reload.py doesn't execute "exit" commands. Because of that, it tries
to execute "interface eth0" inside the "router ospf6" context and fails.
To always execute all commands from the correct context, frr-reload.py
should properly exit from every entered node.
Issue:
Previously, the PBR common was updated for every rule update or deletion
example:
let say we have three rule 11, 12, 13 and if we are removing rule 12. in the current code
we are making the entire map "valid" to false.
pbr-map MAP1 seq 11
match src-ip 90.1.1.2/32
set nexthop 20.1.1.2 swp1
pbr-map MAP1 seq 12
match src-ip 90.1.1.3/32
set nexthop 20.1.1.2 swp1
pbr-map MAP1 seq 13
match src-ip 90.1.1.4/32
set nexthop 20.1.1.2 swp1
no pbr-map MAP1 seq 12 ==> turns whole map valid to false.
r1(config)# end
r1# show pbr map
pbr-map MAP1 valid: no
Seq: 11 rule: 310
Installed: yes Reason: Valid
SRC IP Match: 90.1.1.2/32
nexthop 20.1.1.2 swp1
Installed: yes Tableid: 10002
Seq: 13 rule: 312
Installed: yes Reason: Valid
SRC IP Match: 90.1.1.4/32
nexthop 20.1.1.2 swp1
Installed: yes Tableid: 10004
Fix:
Now, the PBR common will only be updated when the last rule is being deleted.
This change ensures that we only send a delete request to Zebra once, and only
set the valid and installed flags to false when the last rule is deleted.
This optimizes the handling of PBR rules and reduces unnecessary interactions with Zebra
Igor Ryzhov [Tue, 23 Jan 2024 00:32:22 +0000 (02:32 +0200)]
pimd: fix crash when configuring ssmpingd
Command: `ip ssmpingd 1.1.1.1`
Backtrace:
```
__GI_raise (sig=sig@entry=6) at ../sysdeps/unix/sysv/linux/raise.c:50
0x00007fd1d3b02859 in __GI_abort () at abort.c:79
0x00007fd1d3e323e1 in yang_dnode_xpath_get_canon (dnode=<optimized out>, xpath_fmt=<optimized out>, ap=<optimized out>) at lib/yang_wrappers.c:61
0x00007fd1d3e34f41 in yang_dnode_get_ipv4 (addr=addr@entry=0x7ffc368554d4, dnode=<optimized out>, xpath_fmt=xpath_fmt@entry=0x5556af8680d4 "./source-addr") at lib/yang_wrappers.c:826
0x00005556af8216d3 in routing_control_plane_protocols_control_plane_protocol_pim_address_family_ssm_pingd_source_ip_create (args=0x7ffc36855530) at pimd/pim_nb_config.c:925
0x00007fd1d3dec13f in nb_callback_create (nb_node=0x5556b197ea40, nb_node=0x5556b197ea40, errmsg_len=8192, errmsg=0x7ffc36855a90 "", resource=0x5556b18fa6f8, dnode=0x5556b1ad7a10, event=NB_EV_APPLY, context=0x5556b1ad75c0) at lib/northbound.c:1260
nb_callback_configuration (context=0x5556b1ad75c0, event=NB_EV_APPLY, change=<optimized out>, errmsg=0x7ffc36855a90 "", errmsg_len=8192) at lib/northbound.c:1648
0x00007fd1d3deca6c in nb_transaction_process (event=event@entry=NB_EV_APPLY, transaction=transaction@entry=0x5556b1ad75c0, errmsg=errmsg@entry=0x7ffc36855a90 "", errmsg_len=errmsg_len@entry=8192) at lib/northbound.c:1779
0x00007fd1d3decdd6 in nb_candidate_commit_apply (transaction=0x5556b1ad75c0, save_transaction=save_transaction@entry=true, transaction_id=transaction_id@entry=0x0, errmsg=errmsg@entry=0x7ffc36855a90 "", errmsg_len=errmsg_len@entry=8192) at lib/northbound.c:1129
0x00007fd1d3decf15 in nb_candidate_commit (context=..., candidate=<optimized out>, save_transaction=save_transaction@entry=true, comment=comment@entry=0x0, transaction_id=transaction_id@entry=0x0, errmsg=0x7ffc36855a90 "", errmsg_len=8192) at lib/northbound.c:1162
0x00007fd1d3ded4af in nb_cli_classic_commit (vty=vty@entry=0x5556b1ada2a0) at lib/northbound_cli.c:50
0x00007fd1d3df025f in nb_cli_apply_changes_internal (vty=vty@entry=0x5556b1ada2a0, xpath_base=xpath_base@entry=0x7ffc36859b50 ".", clear_pending=clear_pending@entry=false) at lib/northbound_cli.c:177
0x00007fd1d3df06ad in nb_cli_apply_changes (vty=vty@entry=0x5556b1ada2a0, xpath_base_fmt=xpath_base_fmt@entry=0x0) at lib/northbound_cli.c:233
0x00005556af80fdd5 in pim_process_ssmpingd_cmd (vty=0x5556b1ada2a0, operation=NB_OP_CREATE, src_str=0x5556b1ad9630 "1.1.1.1") at pimd/pim_cmd_common.c:3423
0x00007fd1d3da7b0e in cmd_execute_command_real (vline=vline@entry=0x5556b1ac9520, vty=vty@entry=0x5556b1ada2a0, cmd=cmd@entry=0x0, up_level=up_level@entry=0) at lib/command.c:982
0x00007fd1d3da7cb1 in cmd_execute_command (vline=vline@entry=0x5556b1ac9520, vty=vty@entry=0x5556b1ada2a0, cmd=0x0, vtysh=vtysh@entry=0) at lib/command.c:1040
0x00007fd1d3da7e50 in cmd_execute (vty=vty@entry=0x5556b1ada2a0, cmd=cmd@entry=0x5556b1ae0a30 "ip ssmpingd 1.1.1.1", matched=matched@entry=0x0, vtysh=vtysh@entry=0) at lib/command.c:1207
0x00007fd1d3e278be in vty_command (vty=vty@entry=0x5556b1ada2a0, buf=<optimized out>) at lib/vty.c:591
0x00007fd1d3e27afd in vty_execute (vty=0x5556b1ada2a0) at lib/vty.c:1354
0x00007fd1d3e2bb23 in vtysh_read (thread=<optimized out>) at lib/vty.c:2362
0x00007fd1d3e22254 in event_call (thread=thread@entry=0x7ffc3685cd80) at lib/event.c:2003
0x00007fd1d3dce9e8 in frr_run (master=0x5556b183c830) at lib/libfrr.c:1218
0x00005556af803653 in main (argc=6, argv=<optimized out>, envp=<optimized out>) at pimd/pim_main.c:162
```
bgpd: Set correct TTL for the dynamic neighbor peers
In an EBGP multihop configuration with dynamic neighbors, the TTL configured is not being updated for the socket.
Issue:
Assume the following topology:
Host (Dynamic peer to spine - 192.168.1.100) - Leaf - Spine (192.168.1.1)
When the host establishes a BGP multihop session to the spine,
the connection uses the MAXTTL value instead of the configured TTL (in this case, 2).
This issue is only observed with dynamic peers.
Logs: look at the TTL is still MAXTTL, instead of “2” configured.
Olivier Dugeon [Thu, 14 Dec 2023 17:34:38 +0000 (18:34 +0100)]
tests: Update OSPF TE topotests
The OSPF TE topotest is using switches to interconnect router. During the test,
interfaces are shutdown on some routers to simulate link failure and check that
the TED is correctly updated. However, the switche between router avoid the
detection by the neighbor router that the interface is down i.e. the interface
line remains up as it is conneted to the switch and not to the router.
This patch update the tested topology by removing the switch and connect
directly the router excepted the inter AS link on R3. Interface are also
renamed accordingly.
Olivier Dugeon [Thu, 14 Dec 2023 17:22:32 +0000 (18:22 +0100)]
ospfd: Correct LSA parser which fulfill the TED
Traffic Engineering Database (TED) is fulfill from the various LSA advertised
and received by the router. To remove information on the TED, 2 mechanisms are
used: i) parse TE Opaque LSA when there are flushed and ii) compare the list of
prefixes advertised in the Router LSA with the list of corresponding edges and
subnets contained in the TED. However, this second mechanism assumes that the
Router LSA is unique and contains all prefixes of the advertised router.
But, this is wrong. Prefixes could be advertised with several Router LSA.
This conduct to remove edge and subnet in the TED while it should be maintained.
The result is a faulty test with ospf_sr_te_topo1 topotest when server is heavy
loaded.
This simple patch removed deletion of edges and subnets when parsing the Router
LSA and only removed them when the corresponding TE Opaque LSA is flushed. In
addition, TE Opaque LSA are not flushed when OSPF ajacency goes down. This
patch also correct this second problem.
projects / mirror / frr.git / log