Donald Sharp [Fri, 19 Apr 2024 16:13:32 +0000 (12:13 -0400)]
lib, zebra: Check for not being a blackhole route
In zebra_interface_nhg_reinstall zebra is checking that the
nhg is a singleton and not a blackhole nhg. This was originally
done with checking that the nexthop is a NEXTHOP_TYPE_IFINDEX,
NEXTHOP_TYPE_IPV4_IFINDEX and NEXTHOP_TYPE_IPV6_IFINDEX. This
was excluding NEXTHOP_TYPE_IPV4 and NEXTHOP_TYPE_IPV6. These
were both possible to be received and maintained from the upper
level protocol for when a route is being recursively resolved.
If we have gotten to this point in zebra_interface_nhg_reinstall
the nexthop group has already been installed at least once
and we *know* that it is actually a valid nexthop. What the
test is really trying to do is ensure that we are not reinstalling
a blackhole nexthop group( Which is not possible to even be
here by the way, but safety first! ). So let's change
to test for that instead.
Donald Sharp [Thu, 11 Apr 2024 14:46:46 +0000 (10:46 -0400)]
bgpd: Fix display when using `missing-as-worst`
The usage of the `bgp bestpath med missing-as-worst` command
was being accepted and applied during bestpath, but during output
of the routes affected by this it would not give any indication
that this was happening or what med value was being used.
Donald Sharp [Thu, 28 Mar 2024 16:27:38 +0000 (12:27 -0400)]
bgpd: Arrange peer notification to after zebra announce
Currently BGP attempts to send route change information
to it's peers *before* the route is installed into zebra.
This creates a bug in suppress-fib-pending in the following
scenario:
a) bgp suppress-fib-pending and bgp has a route with
2 way ecmp.
b) bgp receives a route withdraw from peer 1. BGP
will send the route to zebra and mark the route as
FIB_INSTALL_PENDING.
c) bgp receives a route withdraw from peer 2. BGP
will see the route has the FIB_INSTALL_PENDING and
not send the withdrawal of the route to the peer.
bgp will then send the route deletion to zebra and
clean up the bgp_path_info's.
At this point BGP is stuck where it has not sent
a route withdrawal to downstream peers.
Let's modify the code in bgp_process_main_one to
send the route notification to zebra first before
attempting to announce the route. The route withdrawal
will remove the FIB_INSTALL_PENDING flag from the dest
and this will allow group_announce_route to believe
it can send the route withdrawal.
For the master branch this is ok because the recent
backpressure commits are in place and nothing is going
to change from an ordering perspective in that regards.
Ostensibly this fix is also for operators of Sonic and
will be backported to the 8.5 branch as well. This will
change the order of the send to peers to be after the
zebra installation but sonic users are using suppress-fib-pending
anyways so updates won't go out until rib ack has been
received anyways.
Donald Sharp [Thu, 28 Mar 2024 16:25:05 +0000 (12:25 -0400)]
bgpd: Note when receiving but not understanding a route notification
When BGP has been asked to wait for FIB installation, on route
removal a return call is likely to not have the dest since BGP
will have cleaned up the node, entirely. Let's just note that
the prefix cannot be found if debugs are turned on and move on.
Donatas Abraitis [Wed, 27 Mar 2024 17:08:38 +0000 (19:08 +0200)]
bgpd: Prevent from one more CVE triggering this place
If we receive an attribute that is handled by bgp_attr_malformed(), use
treat-as-withdraw behavior for unknown (or missing to add - if new) attributes.
Donatas Abraitis [Wed, 27 Mar 2024 16:42:56 +0000 (18:42 +0200)]
bgpd: Fix error handling when receiving BGP Prefix SID attribute
Without this patch, we always set the BGP Prefix SID attribute flag without
checking if it's malformed or not. RFC8669 says that this attribute MUST be discarded.
Also, this fixes the bgpd crash when a malformed Prefix SID attribute is received,
with malformed transitive flags and/or TLVs.
Philippe Guibert [Fri, 29 Mar 2024 07:35:34 +0000 (08:35 +0100)]
bgpd: fix srv6 memory leak detection
The asan memory leak has been detected:
> Direct leak of 16 byte(s) in 1 object(s) allocated from:
> #0 0x7f9066dadd28 in __interceptor_calloc (/usr/lib/x86_64-linux-gnu/libasan.so.4+0xded28)
> #1 0x7f9066779b5d in qcalloc lib/memory.c:105
> #2 0x556d6ca527c2 in vpn_leak_zebra_vrf_sid_update_per_af bgpd/bgp_mplsvpn.c:389
> #3 0x556d6ca530e1 in vpn_leak_zebra_vrf_sid_update bgpd/bgp_mplsvpn.c:451
> #4 0x556d6ca64b3b in vpn_leak_postchange bgpd/bgp_mplsvpn.h:311
> #5 0x556d6ca64b3b in vpn_leak_postchange_all bgpd/bgp_mplsvpn.c:3751
> #6 0x556d6cb9f116 in bgp_zebra_process_srv6_locator_chunk bgpd/bgp_zebra.c:3337
> #7 0x7f906685a6b6 in zclient_read lib/zclient.c:4490
> #8 0x7f9066826a32 in event_call lib/event.c:2011
> #9 0x7f906675c444 in frr_run lib/libfrr.c:1217
> #10 0x556d6c980d52 in main bgpd/bgp_main.c:545
> #11 0x7f9065784c86 in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x21c86)
Fix this by freeing the previous memory chunk.
Fixes: b72c9e14756f ("bgpd: cli for SRv6 SID alloc to redirect to vrf (step4)") Fixes: 527588aa78b2 ("bgpd: add support for per-VRF SRv6 SID") Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
(cherry picked from commit eea8a8ae248ed726449878c7a74705d779469fda)
Donald Sharp [Fri, 6 Oct 2023 16:48:38 +0000 (12:48 -0400)]
bgpd: Convert the bgp_advertise_attr->adv to a fifo
BGP is storing outgoing updates in a couple of different
fifo's. This is to ensure proper packet packing of
all bgp_dests that happen to use the same attribute.
How it's all put together currently: On initial update
BGP walks through all the bgp_dest's in a table. For each
path being sent a bgp_advertise is created. This bgp_advertise
is placed in fifo order on the bgp_synchronize->update queue.
The bgp_advertise has a pointer to the bgp_advertise_attr which
is associated iwth the actual attribute that is being sent to
it's peer. In turn this bgp_advertise is placed in a fifo off
of the bgp_advertise_attr structure. As such as we have paths
that share an attribute, the path/dest is placed on the
bgp_syncrhonize->update fifo as well as being placed on the fifo
associated with the advertised attribute.
On actual creation of a packet. The first item in the
bgp_synchronize->update fifo is popped. The bgp_advertise_attr
pointer is grabbed, we fill out the nlri part of the bgp packet
and then walk the bgp_advertise_attr fifo to place paths/dests in
the packet. As each path/dest is placed in the packet it is removed
from both the bgp_synchronize->update fifo and the bgp_advertise_attr
fifo.
The whole point of this change is to switch the *next, *prev
pointers in the bgp_advertise structure with a typesafe data
structure.
Tomi Salminen [Wed, 13 Dec 2023 09:37:21 +0000 (11:37 +0200)]
zebra: Fix crash on macvlan link down/up
Whenever a link up change was detected on a macvlan device where
the linked device wasn't visible in the namespace zebra was
running in, the linked zebra interface was NULL. This was already
handled in the event of a link down, but was ommitted from the
upside. Added the same null check to the up-side.
Donatas Abraitis [Fri, 15 Mar 2024 11:49:06 +0000 (13:49 +0200)]
bgpd: Update default-originate route-map actual map structure
If using with `bgp listen range ... peer-group x`, default_rmap[afi][safi] is not
updated, and after the hard-reset in other side, this is flushed and never updated
again without restarting the sender BGP daemon.
Split zebra's vrf_terminate() into disable() and delete() stages.
The former enqueues all events for the dplane thread.
Memory freeing is performed in the second stage.
Donald Sharp [Sat, 2 Mar 2024 14:50:38 +0000 (09:50 -0500)]
bgpd: Ensure community data is freed in some cases.
Customer has this valgrind trace:
Direct leak of 2829120 byte(s) in 70728 object(s) allocated from:
0 in community_new ../bgpd/bgp_community.c:39
1 in community_uniq_sort ../bgpd/bgp_community.c:170
2 in route_set_community ../bgpd/bgp_routemap.c:2342
3 in route_map_apply_ext ../lib/routemap.c:2673
4 in subgroup_announce_check ../bgpd/bgp_route.c:2367
5 in subgroup_process_announce_selected ../bgpd/bgp_route.c:2914
6 in group_announce_route_walkcb ../bgpd/bgp_updgrp_adv.c:199
7 in hash_walk ../lib/hash.c:285
8 in update_group_af_walk ../bgpd/bgp_updgrp.c:2061
9 in group_announce_route ../bgpd/bgp_updgrp_adv.c:1059
10 in bgp_process_main_one ../bgpd/bgp_route.c:3221
11 in bgp_process_wq ../bgpd/bgp_route.c:3221
12 in work_queue_run ../lib/workqueue.c:282
The above leak detected by valgrind was from a screenshot so I copied it
by hand. Any mistakes in line numbers are purely from my transcription.
Additionally this is against a slightly modified 8.5.1 version of FRR.
Code inspection of 8.5.1 -vs- latest master shows the same problem
exists. Code should be able to be followed from there to here.
What is happening:
There is a route-map being applied that modifes the outgoing community
to a peer. This is saved in the attr copy created in
subgroup_process_announce_selected. This community pointer is not
interned. So the community->refcount is still 0. Normally when
a prefix is announced, the attr and the prefix are placed on a
adjency out structure where the attribute is interned. This will
cause the community to be saved in the community hash list as well.
In a non-normal operation when the decision to send is aborted after
the route-map application, the attribute is just dropped and the
pointer to the community is just dropped too, leading to situations
where the memory is leaked. The usage of bgp suppress-fib would
would be a case where the community is caused to be leaked.
Additionally the previous commit where an unsuppress-map is used
to modify the outgoing attribute but since unsuppress-map was
not considered part of outgoing policy the attribute would be dropped as
well. This pointer drop also extends to any dynamically allocated
memory saved by the attribute pointer that was not interned yet as well.
So let's modify the return case where the decision is made to
not send the prefix to the peer to always just flush the attribute
to ensure memory is not leaked.
Donald Sharp [Wed, 13 Mar 2024 14:26:58 +0000 (10:26 -0400)]
bgpd: Ensure that the correct aspath is free'd
Currently in subgroup_default_originate the attr.aspath
is set in bgp_attr_default_set, which hashs the aspath
and creates a refcount for it. If this is a withdraw
the subgroup_announce_check and bgp_adj_out_set_subgroup
is called which will intern the attribute. This will
cause the the attr.aspath to be set to a new value
finally at the bottom of the function it intentionally
uninterns the aspath which is not the one that was
created for this function. This reduces the other
aspath's refcount by 1 and if a clear bgp * is issued
fast enough the aspath for that will be removed
and the system will crash.
Louis Scalbert [Thu, 15 Feb 2024 12:28:02 +0000 (13:28 +0100)]
bgpd: fix 6vpe nexthop
6vPE enables the announcement of IPv6 VPN prefixes through an IPv4 BGP
session. In this scenario, the next hop addresses for these prefixes are
represented in an IPv4-mapped IPv6 format, noted as ::ffff:[IPv4]. This
format indicates to the peer that it should route these IPv6 addresses
using information from the IPv4 nexthop. For example:
> Path Attribute - MP_REACH_NLRI
> [...]
> Address family identifier (AFI): IPv6 (2)
> Subsequent address family identifier (SAFI): Labeled VPN Unicast (128)
> Next hop: RD=0:0 IPv6=::ffff:192.0.2.5 RD=0:0 Link-local=fe80::501d:42ff:feef:b021
> Number of Subnetwork points of attachment (SNPA): 0
This rule is set out in RFC4798:
> The IPv4 address of the egress 6PE router MUST be encoded as an
> IPv4-mapped IPv6 address in the BGP Next Hop field.
However, in some situations, bgpd sends a standard nexthop IPv6 address
instead of an IPv4-mapped IPv6 address because the outgoing interface for
the BGP session has a valid IPv6 address. This is problematic because
the peer router may not be able to route the nexthop IPv6 address (ie.
if the outgoing interface has not IPv6).
Fix the issue by always sending a IPv4-mapped IPv6 address as nexthop
when the BGP session is on IPv4 and address family IPv6.
Philippe Guibert [Mon, 13 Mar 2023 09:47:16 +0000 (10:47 +0100)]
topotests: add an ebgp 6vpe test
This test uses the connected ipv4 mapped ipv6 prefix
to resolve the received BGP routes.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com> Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com> Signed-off-by: François Dumontet <francois.dumontet@6wind.com>
(cherry picked from commit 4d7df91752d7414d9719a361a2fd4cc30943dc96)
Louis Scalbert [Tue, 20 Feb 2024 16:49:01 +0000 (17:49 +0100)]
zebra: fix crash if macvlan link in another netns
A macvlan interface can have its underlying link-interface in another
namespace (aka. netns). However, by default, zebra does not know the
interface from the other namespaces. It results in a crash the pointer
to the link interface is NULL.
Fix the crash by returning when the macvlan link-interface is in another
namespace. No need to go further because any vxlan under the macvlan
interface would not be accessible by zebra.
Olivier Dugeon [Mon, 26 Feb 2024 09:40:34 +0000 (10:40 +0100)]
ospfd: Solved crash in OSPF TE parsing
Iggy Frankovic discovered an ospfd crash when perfomring fuzzing of OSPF LSA
packets. The crash occurs in ospf_te_parse_te() function when attemping to
create corresponding egde from TE Link parameters. If there is no local
address, an edge is created but without any attributes. During parsing, the
function try to access to this attribute fields which has not been created
causing an ospfd crash.
The patch simply check if the te parser has found a valid local address. If not
found, we stop the parser which avoid the crash.
adding a tests about:
"no bgp as-path access-list" command.
the folloxing "clear bgp *" command leads to the
crash exhibited above.
a sleep had been added to capture the crash befor the end of scenario.
50 ../sysdeps/unix/sysv/linux/raise.c: No such file or directory.
[Current thread is 1 (Thread 0x7f5f05cbb9c0 (LWP 1371086))]
(gdb) bt
context=0x7ffcf2c216c0) at lib/sigevent.c:248
acl_list=0x55c976ec03c0) at bgpd/bgp_aspath.c:1688
dummy=0x7ffcf2c22340, object=0x7ffcf2c21e70) at bgpd/bgp_routemap.c:2401
match_object=0x7ffcf2c21e70, set_object=0x7ffcf2c21e70, pref=0x0)
at lib/routemap.c:2687
attr=0x7ffcf2c220b0, afi=AFI_IP, safi=SAFI_UNICAST, rmap_name=0x0, label=0x0,
num_labels=0, dest=0x55c976ebeaf0) at bgpd/bgp_route.c:1807
addpath_id=0, attr=0x7ffcf2c22450, afi=AFI_IP, safi=SAFI_UNICAST, type=10,
sub_type=0, prd=0x0, label=0x0, num_labels=0, soft_reconfig=0, evpn=0x0)
at bgpd/bgp_route.c:4424
packet=0x7ffcf2c22410) at bgpd/bgp_route.c:6266
packet=0x7ffcf2c22410, mp_withdraw=false) at bgpd/bgp_packet.c:341
peer=0x55c976e89ed0, size=43) at bgpd/bgp_packet.c:2414
at bgpd/bgp_packet.c:3899
pimd: re-evaluated S,G OILs upon RP changes and for empty SG upstream oils
Topology:
TOR11 (FHR) --- LEAF-11---SPINE1 (RP)MSDP SPINE-2(RP)MSDP --- LEAF-12 -- TOR12 (LHR)
| | | | |
| -----------------------------------------------------(ECMP) |
| | | |
-----------------------------------------------------------------------(ECMP)
Issue:
In some triggers, S,G upstream is preserved even with the PP timer expiry, resulting
in S,G with NULL OILS. This could be because we create a dummy S,G upstream and
dummy channel_oif for *,G, where RPF is UNKNOWN. As a result, PIM+VXLAN traffic is never
forwarded downstream to LHR.
Fix:
when the S,G stream is running, Determine if a reevaluation of the outgoing interface
list (OIL) is required. S,G upstream should then inherit the OIL from *,G.
ospfd: can not delete "segment-routing node-msd" when SR if off
This fixes the initial implementation of commit 7743f2f8c00 ("OSPFd: Update
Segment Routing PR following review") where it wsa not possible to remove
the "segment-routing node-msd" CLI nodes via vtysh once segment-routing got
disabled.
When "no bgp network import-check" is set, it is impossible to
successfully import the static routes into the BGP VPN table. The prefix
is present in the table but is not marked as valid. This issue applies
regardless of whether or not routes are present in the router's RIB.
Always mark as valid the nexthops of BGP static routes when "no bgp
network import-check" is set.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com> Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
(cherry picked from commit 45bf46441a2e0b02650a1d162367c357b220c7b1)
Issue:
Previously, the PBR common was updated for every rule update or deletion
example:
let say we have three rule 11, 12, 13 and if we are removing rule 12. in the current code
we are making the entire map "valid" to false.
pbr-map MAP1 seq 11
match src-ip 90.1.1.2/32
set nexthop 20.1.1.2 swp1
pbr-map MAP1 seq 12
match src-ip 90.1.1.3/32
set nexthop 20.1.1.2 swp1
pbr-map MAP1 seq 13
match src-ip 90.1.1.4/32
set nexthop 20.1.1.2 swp1
no pbr-map MAP1 seq 12 ==> turns whole map valid to false.
r1(config)# end
r1# show pbr map
pbr-map MAP1 valid: no
Seq: 11 rule: 310
Installed: yes Reason: Valid
SRC IP Match: 90.1.1.2/32
nexthop 20.1.1.2 swp1
Installed: yes Tableid: 10002
Seq: 13 rule: 312
Installed: yes Reason: Valid
SRC IP Match: 90.1.1.4/32
nexthop 20.1.1.2 swp1
Installed: yes Tableid: 10004
Fix:
Now, the PBR common will only be updated when the last rule is being deleted.
This change ensures that we only send a delete request to Zebra once, and only
set the valid and installed flags to false when the last rule is deleted.
This optimizes the handling of PBR rules and reduces unnecessary interactions with Zebra
Igor Ryzhov [Tue, 23 Jan 2024 00:32:22 +0000 (02:32 +0200)]
pimd: fix crash when configuring ssmpingd
Command: `ip ssmpingd 1.1.1.1`
Backtrace:
```
__GI_raise (sig=sig@entry=6) at ../sysdeps/unix/sysv/linux/raise.c:50
0x00007fd1d3b02859 in __GI_abort () at abort.c:79
0x00007fd1d3e323e1 in yang_dnode_xpath_get_canon (dnode=<optimized out>, xpath_fmt=<optimized out>, ap=<optimized out>) at lib/yang_wrappers.c:61
0x00007fd1d3e34f41 in yang_dnode_get_ipv4 (addr=addr@entry=0x7ffc368554d4, dnode=<optimized out>, xpath_fmt=xpath_fmt@entry=0x5556af8680d4 "./source-addr") at lib/yang_wrappers.c:826
0x00005556af8216d3 in routing_control_plane_protocols_control_plane_protocol_pim_address_family_ssm_pingd_source_ip_create (args=0x7ffc36855530) at pimd/pim_nb_config.c:925
0x00007fd1d3dec13f in nb_callback_create (nb_node=0x5556b197ea40, nb_node=0x5556b197ea40, errmsg_len=8192, errmsg=0x7ffc36855a90 "", resource=0x5556b18fa6f8, dnode=0x5556b1ad7a10, event=NB_EV_APPLY, context=0x5556b1ad75c0) at lib/northbound.c:1260
nb_callback_configuration (context=0x5556b1ad75c0, event=NB_EV_APPLY, change=<optimized out>, errmsg=0x7ffc36855a90 "", errmsg_len=8192) at lib/northbound.c:1648
0x00007fd1d3deca6c in nb_transaction_process (event=event@entry=NB_EV_APPLY, transaction=transaction@entry=0x5556b1ad75c0, errmsg=errmsg@entry=0x7ffc36855a90 "", errmsg_len=errmsg_len@entry=8192) at lib/northbound.c:1779
0x00007fd1d3decdd6 in nb_candidate_commit_apply (transaction=0x5556b1ad75c0, save_transaction=save_transaction@entry=true, transaction_id=transaction_id@entry=0x0, errmsg=errmsg@entry=0x7ffc36855a90 "", errmsg_len=errmsg_len@entry=8192) at lib/northbound.c:1129
0x00007fd1d3decf15 in nb_candidate_commit (context=..., candidate=<optimized out>, save_transaction=save_transaction@entry=true, comment=comment@entry=0x0, transaction_id=transaction_id@entry=0x0, errmsg=0x7ffc36855a90 "", errmsg_len=8192) at lib/northbound.c:1162
0x00007fd1d3ded4af in nb_cli_classic_commit (vty=vty@entry=0x5556b1ada2a0) at lib/northbound_cli.c:50
0x00007fd1d3df025f in nb_cli_apply_changes_internal (vty=vty@entry=0x5556b1ada2a0, xpath_base=xpath_base@entry=0x7ffc36859b50 ".", clear_pending=clear_pending@entry=false) at lib/northbound_cli.c:177
0x00007fd1d3df06ad in nb_cli_apply_changes (vty=vty@entry=0x5556b1ada2a0, xpath_base_fmt=xpath_base_fmt@entry=0x0) at lib/northbound_cli.c:233
0x00005556af80fdd5 in pim_process_ssmpingd_cmd (vty=0x5556b1ada2a0, operation=NB_OP_CREATE, src_str=0x5556b1ad9630 "1.1.1.1") at pimd/pim_cmd_common.c:3423
0x00007fd1d3da7b0e in cmd_execute_command_real (vline=vline@entry=0x5556b1ac9520, vty=vty@entry=0x5556b1ada2a0, cmd=cmd@entry=0x0, up_level=up_level@entry=0) at lib/command.c:982
0x00007fd1d3da7cb1 in cmd_execute_command (vline=vline@entry=0x5556b1ac9520, vty=vty@entry=0x5556b1ada2a0, cmd=0x0, vtysh=vtysh@entry=0) at lib/command.c:1040
0x00007fd1d3da7e50 in cmd_execute (vty=vty@entry=0x5556b1ada2a0, cmd=cmd@entry=0x5556b1ae0a30 "ip ssmpingd 1.1.1.1", matched=matched@entry=0x0, vtysh=vtysh@entry=0) at lib/command.c:1207
0x00007fd1d3e278be in vty_command (vty=vty@entry=0x5556b1ada2a0, buf=<optimized out>) at lib/vty.c:591
0x00007fd1d3e27afd in vty_execute (vty=0x5556b1ada2a0) at lib/vty.c:1354
0x00007fd1d3e2bb23 in vtysh_read (thread=<optimized out>) at lib/vty.c:2362
0x00007fd1d3e22254 in event_call (thread=thread@entry=0x7ffc3685cd80) at lib/event.c:2003
0x00007fd1d3dce9e8 in frr_run (master=0x5556b183c830) at lib/libfrr.c:1218
0x00005556af803653 in main (argc=6, argv=<optimized out>, envp=<optimized out>) at pimd/pim_main.c:162
```
bgpd: Set correct TTL for the dynamic neighbor peers
In an EBGP multihop configuration with dynamic neighbors, the TTL configured is not being updated for the socket.
Issue:
Assume the following topology:
Host (Dynamic peer to spine - 192.168.1.100) - Leaf - Spine (192.168.1.1)
When the host establishes a BGP multihop session to the spine,
the connection uses the MAXTTL value instead of the configured TTL (in this case, 2).
This issue is only observed with dynamic peers.
Logs: look at the TTL is still MAXTTL, instead of “2” configured.
> ==3901635==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x6020003a5940 at pc 0x56260067bb48 bp 0x7ffe8a4f3840 sp 0x7ffe8a4f3838
> READ of size 4 at 0x6020003a5940 thread T0
> #0 0x56260067bb47 in ecommunity_fill_pbr_action bgpd/bgp_ecommunity.c:1587
> #1 0x5626007a246e in bgp_pbr_build_and_validate_entry bgpd/bgp_pbr.c:939
> #2 0x5626007b25e6 in bgp_pbr_update_entry bgpd/bgp_pbr.c:2933
> #3 0x562600909d18 in bgp_zebra_announce bgpd/bgp_zebra.c:1351
> #4 0x5626007d5efd in bgp_process_main_one bgpd/bgp_route.c:3528
> #5 0x5626007d6b43 in bgp_process_wq bgpd/bgp_route.c:3641
> #6 0x7f450f34c2cc in work_queue_run lib/workqueue.c:266
> #7 0x7f450f327a27 in event_call lib/event.c:1970
> #8 0x7f450f21a637 in frr_run lib/libfrr.c:1213
> #9 0x56260062fc04 in main bgpd/bgp_main.c:540
> #10 0x7f450ee2dd09 in __libc_start_main ../csu/libc-start.c:308
> #11 0x56260062ca29 in _start (/usr/lib/frr/bgpd+0x2e3a29)
>
> 0x6020003a5940 is located 0 bytes to the right of 16-byte region [0x6020003a5930,0x6020003a5940)
> allocated by thread T0 here:
> #0 0x7f450f6aa1f8 in __interceptor_realloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:164
> #1 0x7f450f244f8a in qrealloc lib/memory.c:112
> #2 0x562600673313 in ecommunity_add_val_internal bgpd/bgp_ecommunity.c:143
> #3 0x5626006735bc in ecommunity_uniq_sort_internal bgpd/bgp_ecommunity.c:193
> #4 0x5626006737e3 in ecommunity_parse_internal bgpd/bgp_ecommunity.c:228
> #5 0x562600673890 in ecommunity_parse bgpd/bgp_ecommunity.c:236
> #6 0x562600640469 in bgp_attr_ext_communities bgpd/bgp_attr.c:2674
> #7 0x562600646eb3 in bgp_attr_parse bgpd/bgp_attr.c:3893
> #8 0x562600791b7e in bgp_update_receive bgpd/bgp_packet.c:2141
> #9 0x56260079ba6b in bgp_process_packet bgpd/bgp_packet.c:3406
> #10 0x7f450f327a27 in event_call lib/event.c:1970
> #11 0x7f450f21a637 in frr_run lib/libfrr.c:1213
> #12 0x56260062fc04 in main bgpd/bgp_main.c:540
> #13 0x7f450ee2dd09 in __libc_start_main ../csu/libc-start.c:308
Fixes: dacf6ec120 ("bgpd: utility routine to convert flowspec actions into pbr actions") Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
(cherry picked from commit 6001c765e2a2ede2c98137b82ec8b4550a51dda9)
Louis Scalbert [Wed, 3 Jan 2024 15:13:02 +0000 (16:13 +0100)]
isisd: fix _isis_spftree_del heap-use-after-free
Fix the following heap-use-after-free
> ==82961==ERROR: AddressSanitizer: heap-use-after-free on address 0x6020001e4750 at pc 0x55a8cc7f63ac bp 0x7ffd6948e340 sp 0x7ffd6948e330
> READ of size 8 at 0x6020001e4750 thread T0
> #0 0x55a8cc7f63ab in isis_route_node_cleanup isisd/isis_route.c:335
> #1 0x7ff25ec617c1 in route_node_free lib/table.c:75
> #2 0x7ff25ec619fc in route_table_free lib/table.c:111
> #3 0x7ff25ec61661 in route_table_finish lib/table.c:46
> #4 0x55a8cc800d83 in _isis_spftree_del isisd/isis_spf.c:397
> #5 0x55a8cc800e45 in isis_spftree_clear isisd/isis_spf.c:414
> #6 0x55a8cc80bd9a in isis_run_spf isisd/isis_spf.c:2020
> #7 0x55a8cc80c370 in isis_run_spf_with_protection isisd/isis_spf.c:2076
> #8 0x55a8cc80cf52 in isis_run_spf_cb isisd/isis_spf.c:2165
> #9 0x7ff25ec7c4dc in event_call lib/event.c:1970
> #10 0x7ff25eb64423 in frr_run lib/libfrr.c:1213
> #11 0x55a8cc7799da in main isisd/isis_main.c:318
> #12 0x7ff25e623d8f in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58
> #13 0x7ff25e623e3f in __libc_start_main_impl ../csu/libc-start.c:392
> #14 0x55a8cc778e44 in _start (/usr/lib/frr/isisd+0x109e44)
>
> 0x6020001e4750 is located 0 bytes inside of 16-byte region [0x6020001e4750,0x6020001e4760)
> freed by thread T0 here:
> #0 0x7ff25f000537 in __interceptor_free ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:127
> #1 0x7ff25eb9012e in qfree lib/memory.c:130
> #2 0x55a8cc7f6485 in isis_route_table_info_free isisd/isis_route.c:351
> #3 0x55a8cc800cf4 in _isis_spftree_del isisd/isis_spf.c:395
> #4 0x55a8cc800e45 in isis_spftree_clear isisd/isis_spf.c:414
> #5 0x55a8cc80bd9a in isis_run_spf isisd/isis_spf.c:2020
> #6 0x55a8cc80c370 in isis_run_spf_with_protection isisd/isis_spf.c:2076
> #7 0x55a8cc80cf52 in isis_run_spf_cb isisd/isis_spf.c:2165
> #8 0x7ff25ec7c4dc in event_call lib/event.c:1970
> #9 0x7ff25eb64423 in frr_run lib/libfrr.c:1213
> #10 0x55a8cc7799da in main isisd/isis_main.c:318
> #11 0x7ff25e623d8f in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58
>
> previously allocated by thread T0 here:
> #0 0x7ff25f000a57 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154
> #1 0x7ff25eb8ffdc in qcalloc lib/memory.c:105
> #2 0x55a8cc7f63eb in isis_route_table_info_alloc isisd/isis_route.c:343
> #3 0x55a8cc80052a in _isis_spftree_init isisd/isis_spf.c:334
> #4 0x55a8cc800e51 in isis_spftree_clear isisd/isis_spf.c:415
> #5 0x55a8cc80bd9a in isis_run_spf isisd/isis_spf.c:2020
> #6 0x55a8cc80c370 in isis_run_spf_with_protection isisd/isis_spf.c:2076
> #7 0x55a8cc80cf52 in isis_run_spf_cb isisd/isis_spf.c:2165
> #8 0x7ff25ec7c4dc in event_call lib/event.c:1970
> #9 0x7ff25eb64423 in frr_run lib/libfrr.c:1213
> #10 0x55a8cc7799da in main isisd/isis_main.c:318
> #11 0x7ff25e623d8f in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58
Fixes: 7153c3cabf ("isisd: update struct isis_route_info has multiple sr info by algorithm") Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
(cherry picked from commit 9fa9a9d865c6e0ed2454abf3961410edabb17533)
Olivier Dugeon [Thu, 14 Dec 2023 17:34:38 +0000 (18:34 +0100)]
tests: Update OSPF TE topotests
The OSPF TE topotest is using switches to interconnect router. During the test,
interfaces are shutdown on some routers to simulate link failure and check that
the TED is correctly updated. However, the switche between router avoid the
detection by the neighbor router that the interface is down i.e. the interface
line remains up as it is conneted to the switch and not to the router.
This patch update the tested topology by removing the switch and connect
directly the router excepted the inter AS link on R3. Interface are also
renamed accordingly.
Olivier Dugeon [Thu, 14 Dec 2023 17:22:32 +0000 (18:22 +0100)]
ospfd: Correct LSA parser which fulfill the TED
Traffic Engineering Database (TED) is fulfill from the various LSA advertised
and received by the router. To remove information on the TED, 2 mechanisms are
used: i) parse TE Opaque LSA when there are flushed and ii) compare the list of
prefixes advertised in the Router LSA with the list of corresponding edges and
subnets contained in the TED. However, this second mechanism assumes that the
Router LSA is unique and contains all prefixes of the advertised router.
But, this is wrong. Prefixes could be advertised with several Router LSA.
This conduct to remove edge and subnet in the TED while it should be maintained.
The result is a faulty test with ospf_sr_te_topo1 topotest when server is heavy
loaded.
This simple patch removed deletion of edges and subnets when parsing the Router
LSA and only removed them when the corresponding TE Opaque LSA is flushed. In
addition, TE Opaque LSA are not flushed when OSPF ajacency goes down. This
patch also correct this second problem.
Donald Sharp [Mon, 11 Dec 2023 15:46:53 +0000 (10:46 -0500)]
bgpd: Make `suppress-fib-pending` clear peering
When a peer has come up and already started installing
routes into the rib and `suppress-fib-pending` is either
turned on or off. BGP is left with some routes that
may need to be withdrawn from peers and routes that
it does not know the status of. Clear the BGP peers
for the interesting parties and let's let us come
up to speed as needed.
Olivier Dugeon [Thu, 7 Dec 2023 13:53:16 +0000 (14:53 +0100)]
ospfd: Correct SID check size
Segment Router Identifier (SID) could be an index (4 bytes) within a range
(SRGB or SRLB) or an MPLS label (3 bytes). Thus, before calling check_size
macro to verify SID TLVs size, it is mandatory to determine the SID type to
avoid wrong assert.
Donald Sharp [Mon, 6 Nov 2023 18:02:01 +0000 (13:02 -0500)]
bgpd: Ensure BGP does not stop monitoring nexthops
In some cases BGP can be monitoring the same prefix
in both the nexthop and import check tables. If this
is the case, when unregistering one bnc from one table
make sure we are not still registered in the other
Example of the problem:
r1(config-router)# address-family ipv4 uni
r1(config-router-af)# no network 192.168.100.41/32
r1(config-router-af)# exit
r1# show bgp import-check-table
Current BGP import check cache:
r1# show bgp nexthop
Current BGP nexthop cache:
192.168.100.41 valid [IGP metric 0], #paths 1, peer 192.168.100.41
if r1-eth0
Last update: Wed Dec 6 11:01:40 2023
BGP now believes it is only watching 192.168.100.41 in the nexthop
cache, but zebra doesn't have anything:
r1# show ip import-check
VRF default:
Resolve via default: on
r1# show ip nht
VRF default:
Resolve via default: on
So if anything happens to the route that is being matched for
192.168.100.41 bgp is no longer going to be notified about this.
The source of this problem is that zebra has dropped the two different
tables into 1 table, while bgp has 2 tables to track this. The solution
to this problem (other than the rewrite that is being done ) is to have
BGP have a bit of smarts about looking in both tables for the bnc and
if found in both don't send the delete of the prefix tracking to zebra.
projects / mirror / frr.git / log