Rafael Zalamena [Sat, 3 Nov 2018 22:08:33 +0000 (19:08 -0300)]
bfdd: fix BGP unnumbered peer setup
The session key uses the scope id to figure out which interface we are
using with that link-local address, so if we don't set it when
registering a session we'll end up with multiple IPv6 sessions.
Olivier Dugeon [Fri, 26 Oct 2018 17:12:41 +0000 (19:12 +0200)]
OSPF: Add support to multi-area to Router Info.
Router Information needs to specify the area ID when flooding scope is set to
AREA. However, this authorize only one AREA. Thus, Area Border Router (ABR) are
unable to flood Router Information Opaque LSA in all areas they are belongs to.
The path implies that the area ID is no more necessary for the command
'router-info area'. It remains suported for compatibility, but mark as
deprecated. Documentation has been updated accordingly.
Donald Sharp [Tue, 6 Nov 2018 20:55:36 +0000 (15:55 -0500)]
bgpd: Late registration of Extended Nexthop should allow RA's to happen
When we have a late registration of the Extended Nexthop capability
for BGP and the peer already has nexthop information stored, go
through and enable RA on the important interfaces.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
watchfrr: Echo statements are blocking the execution of frr script
1) Certain echo statements present in the script before/after SSD process
restart are causing the FRR script to hang. This is breaking the frr script
functionality for start/stop/restart. Removed such echo statements.
Tests:
1. Multiple start, stop, restart
2. Multiple restarts/kill of same process.
Signed-off-by: Sri Mohana Singamsetty <msingamsetty@vmware.com>
Renato Westphal [Sat, 3 Nov 2018 17:27:33 +0000 (15:27 -0200)]
doc: update libyang build instructions
The --with-yangmodelsdir and --with-libyang-pluginsdir build-time options
pertain to FRR so they shouldn't be placed along with the libyang build
instructions. Move these instructions to where they belong to avoid
confusion.
Donald Sharp [Tue, 30 Oct 2018 19:12:07 +0000 (15:12 -0400)]
pimd: Send 1 on all systems for MRT_INIT
When sending a sockoption for MRT_INIT, *bsd requires that
the data passed in must be 1. While linux does not, the
code was sending in a positive value that was causing issues
on *bsd of protocol not supported.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Donald Sharp [Fri, 5 Oct 2018 15:31:29 +0000 (11:31 -0400)]
bgpd: Allow registration of nexthops after zebra connection
If we attempt to register nexthops before we have the zebra
connection, they will not be installed. After we have noticed
that we are up, re-install them.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
zebra: set remoteseq to 0 when remote mac is deleted by bgpd
When the remote mac is deleted by bgpd we can end up with an auto mac
entry in zebra if there are neighs referring to the mac. The remote sequence
number in the auto mac entry needs to be reset to 0 as the mac entry may
have been removed on all VTEPs (including the originating one).
Now if the MAC comes back on a remote VTEP it may be added with MM=0 which
will NOT be accepted if the remote seq was not reset in the previous step.
zebra: make neigh active when it is modified from local to remote
This is a fixup to commit - f32ea5c07 - zebra: act on kernel notifications for remote neighbors
The original commit handled a race condition between kernel and zebra
that would result in an inconsistent state i.e.
kernel has an offload/remote neigh
zebra has a local neigh
The original commit missed setting the neigh to active when zebra
tried to resolve the inconsistency by modifying the local neigh to
remote neigh on hearing back its own kernel update. Fixed here.
bgpd: use IP address as tie breaker if the MM seq number is the same
Same sequence number handling is specified by RFC 7432 -
[
If two (or more) PEs advertise the same MAC address with the same
sequence number but different Ethernet segment identifiers, a PE that
receives these routes selects the route advertised by the PE with the
lowest IP address as the best route.
If the PE is the originator of the MAC route and it receives the same
MAC address with the same sequence number that it generated, it will
compare its own IP address with the IP address of the remote PE and
will select the lowest IP. If its own route is not the best one, it
will withdraw the route.
]
To implement that specification this commit uses nexthop IP as a tie
breaker between two paths of equal seq number with lower IP winning.
Now if a local path already exists with the same sequence number but higher
(local-VTEP) IP it is evicted (deleted and withdrawn from the peers) and
the winning new remote path is installed in zebra. This is existing code
and handled implicitly via evpn_route_select_install.
If a local path is rxed from zebra with the same sequence as the
current remote winner it is rejected (not installed in the bgp
routing tables) and zebra is asked to re-install the older/remote winner.
This is a race condition that can only happen if bgp's add and zebra's add
cross paths. Additional handling has been added in this commit via
evpn_cleanup_local_non_best_route to take care of the race condition.
zebra: send a local-mac del to bgpd on mac mod to remote
When events cross paths between bgp and zebra bgpd could end up with a
dangling local MAC entry. Consider the following sequence of events on
rack-1 -
1. MAC1 has MM sequence number 1 and points to rack-3
2. Now a packet is rxed locally on rack-1 and rack-2 (simultaneously) with
source-mac=MAC1.
3. This would cause rack-1 and rack-2 to set the MM seq to 2 and
simultaneously report the MAC as local.
4. Now let's say on rack-1 zebra's MACIP_ADD is in bgpd's queue. bgpd
accepts rack-3's update and sends a remote MACIP add to zebra with MM=2.
5. zebra updates the MAC entry from local=>remote.
6. bgpd now processes zebra's "stale local" making it the best path.
However zebra no longer has a local MAC entry.
At this point bgpd and zebra are effectively out of sync i.e. bgpd has a
local-MAC which is not present in the kernel or in zebra.
To handle this window zebra should send a local MAC delete to bgpd on
modifying its cache to remote.
Don Slice [Fri, 20 Jul 2018 15:02:15 +0000 (15:02 +0000)]
bgpd: make name of default vrf/bgp instance consistent
Problems were reported with the name of the default vrf and the
default bgp instance being different, creating confusion. This
fix changes both to "default" for consistency.
Ticket: CM-21791 Signed-off-by: Don Slice <dslice@cumulusnetworks.com> Reviewed-by: CCR-7658
Testing: manual testing and automated tests before pushing
Mark Stapp [Tue, 30 Oct 2018 18:05:47 +0000 (14:05 -0400)]
zebra: temporary workaround for a clang issue with atomics
Current clang has an issue with the pointer/target argument
to at least one atomic/intrinsic. A variable with '_Atomic'
generates a compile-time error. Use a cast as a workaround
here to allow use of clang for now.
Mark Stapp [Tue, 30 Oct 2018 13:41:55 +0000 (09:41 -0400)]
zebra: only uninstall once, when closing rib table
When the rib code is informed that a table is closing/
going away, only try once to uninstall associated routes from
the fib/dataplane. The close path can be called multiple times
in some cases - zebra shutdown, e.g.
David Lamparter [Sat, 27 Oct 2018 17:06:22 +0000 (19:06 +0200)]
build: crop excessive net-snmp library list
This fixes the longstanding GPL vs. OpenSSL licensing issue in our SNMP
code (and cuts down on its other dependencies a wee bit.)
In a way, net-snmp is really buggy here in what it says that we should
link against, but I don't know their application scenarios well enough
to say it should be changed at their end.
Signed-off-by: David Lamparter <equinox@diac24.net>
Renato Westphal [Sat, 20 Oct 2018 14:37:39 +0000 (11:37 -0300)]
tools: update checkpatch to allow indented labels
clang-format always indent labels by default and that can't be changed
with any configuration option. Also, indented labels tend to improve
code readability, especially in long functions.
projects / mirror / frr.git / log