David Lamparter [Wed, 1 Jun 2022 07:54:31 +0000 (09:54 +0200)]
pimd: try to reinstall MFC when we get NOCACHE
Whether due to a pimd bug, some expiry, or someone just deleting MFC
entries, when we're in NOCACHE we *know* there's no MFC entry. Add an
install call to make sure pimd's MFC view aligns with the actual kernel
MFC.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
David Lamparter [Thu, 10 Mar 2022 12:59:26 +0000 (13:59 +0100)]
pimd: make logs useful for input drops
This path here is pretty far on top of the list of issues that operators
will run into and have to debug when setting up PIM. Make the log
messages actually tell what's going on. Also escalate some from
`debug mroute detail` to `debug mroute`.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Trey Aspelund [Fri, 17 Feb 2023 21:47:09 +0000 (21:47 +0000)]
lib: skip route-map optimization if !AF_INET(6)
Currently we unconditionally send a prefix through the optimized
route-map codepath if the v4 and v6 LPM tables have been allocated and
optimization has not been disabled.
However prefixes from address-families that are not IPv4/IPv6 unicast
always fail the optimized route-map index lookup, because they occur on
an LPM tree that is IPv4 or IPv6 specific.
e.g.
Even if you have an empty permit route-map clause, Type-3 EVPN routes
are always denied:
```
--config
route-map soo-foo permit 10
--logs
2023/02/17 19:38:42 BGP: [KZK58-6T4Y6] No best match sequence for pfx: [3]:[0]:[32]:[2.2.2.2] in route-map: soo-foo, result: no match
2023/02/17 19:38:42 BGP: [H5AW4-JFYQC] Route-map: soo-foo, prefix: [3]:[0]:[32]:[2.2.2.2], result: deny
```
There is some existing code that creates an AF_INET/AF_INET6 prefix
using the IP/prefix information from a Type-2/5 EVPN route, which
allowed only these two route-types to successfully attempt an LPM lookup
in the route-map optimization trees via the converted prefix.
This commit does 3 things:
1) Reverts to non-optimized route-map lookup for prefixes that are not
AF_INET or AF_INET6.
2) Cleans up the route-map code so that the AF check is part of the
index lookup + the EVPN RT-2/5 -> AF_INET/6 prefix conversion occurs
outside the index lookup.
3) Adds "debug route-map detail" logs to indicate when we attempt to
convert an AF_EVPN prefix into an AF_INET/6 prefix + when we fallback
to a non-optimized lookup.
Additional functionality for optimized lookups of prefixes from other
address-families can be added prior to the index lookup, similar to how
the existing EVPN conversion works today.
New behavior:
```
2023/02/17 21:44:27 BGP: [WYP1M-NE4SY] Converted EVPN prefix [5]:[0]:[32]:[192.0.2.7] into 192.0.2.7/32 for optimized route-map lookup
2023/02/17 21:44:27 BGP: [MT1SJ-WEJQ1] Best match route-map: soo-foo, sequence: 10 for pfx: 192.0.2.7/32, result: match
2023/02/17 21:44:27 BGP: [H5AW4-JFYQC] Route-map: soo-foo, prefix: 192.0.2.7/32, result: permit
2023/02/17 21:44:27 BGP: [WYP1M-NE4SY] Converted EVPN prefix [2]:[0]:[48]:[aa:bb:cc:00:22:22]:[32]:[20.0.0.2] into 20.0.0.2/32 for optimized route-map lookup
2023/02/17 21:44:27 BGP: [MT1SJ-WEJQ1] Best match route-map: soo-foo, sequence: 10 for pfx: 20.0.0.2/32, result: match
2023/02/17 21:44:27 BGP: [H5AW4-JFYQC] Route-map: soo-foo, prefix: 20.0.0.2/32, result: permit
2023/02/17 21:44:27 BGP: [KHG7H-RH4PN] Unable to convert EVPN prefix [3]:[0]:[32]:[2.2.2.2] into IPv4/IPv6 prefix. Falling back to non-optimized route-map lookup
2023/02/17 21:44:27 BGP: [MT1SJ-WEJQ1] Best match route-map: soo-foo, sequence: 10 for pfx: [3]:[0]:[32]:[2.2.2.2], result: match
2023/02/17 21:44:27 BGP: [H5AW4-JFYQC] Route-map: soo-foo, prefix: [3]:[0]:[32]:[2.2.2.2], result: permit
```
Donatas Abraitis [Fri, 17 Feb 2023 16:28:17 +0000 (18:28 +0200)]
bgpd: Deprecate BGP `internet` community
Quite a few well-known communities from IANA's list do
not receive special treatment in Cisco IOS XR, and at least one
community on Cisco IOS XR's special treatment list, internet == 0:0,
is not formally a well-known community as it is not in [IANA-WKC] (it
is taken from the Reserved range [0x00000000-0x0000FFFF]).
https://datatracker.ietf.org/doc/html/rfc8642
This is Cisco-specific command which is causing lots of questions when it
comes to debugging and/or configuring it properly, but overall, this behavior
is very odd and it's not clear how it should be treated between different
vendor implementations.
Let's deprecate it and let the operators use 0:0/0 communities as they want.
Trey Aspelund [Mon, 13 Feb 2023 22:14:16 +0000 (22:14 +0000)]
tests: update tests using 'show bgp json detail'
There were a few tests using "show bgp ... json detail" that did json
comparisons against a predefined json structure. This updates those
predefined json structures to match the new format of the output.
(new output moves path array under "paths" key and adds header keys)
Trey Aspelund [Fri, 10 Feb 2023 19:05:27 +0000 (19:05 +0000)]
bgpd: fix 'json detail' output structure
"show bgp <afi> <safi> json detail" was incorrectly displaying header
information from route_vty_out_detail_header() as an element of the
"paths" array. This corrects the behavior for 'json detail' so that a
route holds a dictionary with keys for "paths" and header info, which
aligns with how we structure the output for a specific prefix, e.g.
"show bgp <afi> <safi> <prefix> json".
Before:
```
ub20# show ip bgp json detail
{
"vrfId": 0,
"vrfName": "default",
"tableVersion": 3,
"routerId": "100.64.0.222",
"defaultLocPrf": 100,
"localAS": 1,
"routes": { "2.2.2.2/32": [
{ <<<<<<<<< should be outside the array
"prefix":"2.2.2.2/32",
"version":1,
"advertisedTo":{
"192.168.122.12":{
"hostname":"ub20-2"
}
}
},
{
"aspath":{
"string":"Local",
"segments":[
],
"length":0
},
<snip>
```
Donald Sharp [Thu, 2 Feb 2023 21:28:27 +0000 (16:28 -0500)]
lib: Fix non-use of option
Commit d7c6467ba2f55d1055babbb7fe82716ca3efdc7e added the
ability to specify non pretty printing but unfortunately
forgot to use the option variable to make the whole
thing work.
vivek [Fri, 18 Dec 2020 18:55:40 +0000 (10:55 -0800)]
bgpd: Prevent multipathing among EVPN and non-EVPN paths
Ensure that a multipath set is fully comprised of EVPN paths (i.e.,
paths imported into the VRF from EVPN address-family) or non-EVPN
paths. This is actually a condition that existed already in the code
but was not properly enforced.
This change, as a side effect, eliminates the known trigger condition
for bad or missing RMAC programming in an EVPN deployment, described
in tickets CM-29043 and CM-31222. Routes (actually, paths) in a VRF
routing table that require VXLAN tunneling to the next hop currently
need some special handling in zebra to deal with the nexthop (neigh)
and RMAC programming, and this is implemented for the entire route
(prefix), not per-path. This can lead to the bad or missing RMAC
situation, which is now eliminated by ensuring all paths in the route
are 'similar'.
The longer-term solution in CL 5.x will be to deal with the special
programming by means of explicit communication between bgpd and zebra.
This is already implemented for EVPN-MH via CM-31398. These changes
will be extended to non-MH also and the special code in zebra removed
or refined.
Signed-off-by: Vivek Venkatraman <vivek@nvidia.com> Acked-by: Trey Aspelund <taspelund@nvidia.com> Acked-by: Anuradha Karuppiah <anuradhak@nvidia.com> Acked-by: Chirag Shah <chirag@nvidia.com>
Ticket: CM-29043
Testing Done:
1. Manual testing
2. precommit on both MLX and BCM platforms
3. evpn-smoke - BCM and VX
vivek [Thu, 3 Dec 2020 04:04:19 +0000 (20:04 -0800)]
bgpd: Fix deterministic-med check for stale paths
When performing deterministic MED processing, ensure that the peer
status is not checked when we encounter a stale path. Otherwise, this
path will be skipped from the DMED consideration leading to it potentially
not being installed.
Test scenario: Consider a prefix with 2 (multi)paths. The peer that
announces the path with the winning DMED undergoes a graceful-restart.
Before it comes back up, the other path goes away. Prior to the fix, a
third router that receives both these paths would have ended up not
having any path installed to the prefix after the above events.
Karl Quan [Tue, 14 Feb 2023 15:54:59 +0000 (07:54 -0800)]
bgpd: BGP troubleshooting - Add a keyword self-originate to display only self-originated prefixes when looking at the BGP table for a given address-family
Add a keyword self-originate" to extend current CLI commands to filter out self-originated routes only
a\) CLI to show ipv4/ipv6 self-originated routes
"show [ip] bgp [afi] [safi] [all] self-originate [wide|json]"
b\) CLI to show evpn self-originated routes
"show bgp l2vpn evpn route [detail] [type <ead|macip|multicast|es|prefix|1|2|3|4|5>] self-originate [json]"
```
% ./gobgp neighbor 192.168.10.124
BGP neighbor is 192.168.10.124, remote AS 65001
BGP version 4, remote router ID 200.200.200.202
BGP state = ESTABLISHED, up for 00:01:49
BGP OutQ = 0, Flops = 0
Hold time is 3, keepalive interval is 1 seconds
Configured hold time is 90, keepalive interval is 30 seconds
Neighbor capabilities:
multiprotocol:
ipv4-unicast: advertised and received
ipv6-unicast: advertised
route-refresh: advertised and received
extended-nexthop: advertised
Local: nlri: ipv4-unicast, nexthop: ipv6
UnknownCapability(6): received
UnknownCapability(9): received
graceful-restart: advertised and received
Local: restart time 10 sec
ipv6-unicast
ipv4-unicast
Remote: restart time 120 sec, notification flag set
ipv4-unicast, forward flag set
4-octet-as: advertised and received
add-path: received
Remote:
ipv4-unicast: receive
enhanced-route-refresh: received
long-lived-graceful-restart: advertised and received
Local:
ipv6-unicast, restart time 10 sec
ipv4-unicast, restart time 20 sec
Remote:
ipv4-unicast, restart time 0 sec, forward flag set
fqdn: advertised and received
Local:
name: donatas-pc, domain:
Remote:
name: spine1-debian-11, domain:
software-version: advertised and received
Local:
GoBGP/3.10.0
Remote:
FRRouting/8.5-dev-MyOwnFRRVersion-gdc92f44a45-dirt
cisco-route-refresh: received
Message statistics:
```
Philippe Guibert [Mon, 13 Feb 2023 11:18:33 +0000 (12:18 +0100)]
bgpd: clarify when the vpnv6 nexthop length must be modified
Using a route-map to update the local ipv6 address has to be
better clarified. Actually, when a VPN SAFI is used, the nexthop
length must be changed to 48 bytes. Other cases, the length will
be 32 bytes.
Fixes: 9795e9f23465 ("bgpd: fix when route-map changes the link local
nexthop for vpnv6")
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
zyxwvu Shi [Wed, 15 Feb 2023 15:55:00 +0000 (23:55 +0800)]
zebra: Fix other table inactive when ip import-table is on
In `rib_link`, if is_zebra_import_table_enabled returns
true, `rib_queue_add` will not called, resulting in other
table route node never processed. This actually should not
be dependent on whether the route is imported.
In `rib_delnode`, if is_zebra_import_table_enabled returns
true, it will use `rib_unlink` instead of enqueuing the
route node for process. There is no reason that imported
route nodes should not be reprocessed. Long ago, the
behaviour was dependent on whether the route_entry comes
from a table other than main.
Donald Sharp [Tue, 14 Feb 2023 20:26:44 +0000 (15:26 -0500)]
bgpd: Remove unnecessary all_digit() call
The call for all_digit is unnecessary as that the local preference
must be entered as a digit. In other words you cannot get to this
point without the string being all digits. This check is unnecessary.
Stephen Worley [Thu, 9 Feb 2023 19:57:31 +0000 (14:57 -0500)]
zebra: add VNI info to flood entry
When we are installing the flood entry for a vtep in SVD,
ensure VNI is set on the ctx object so that it gets
sent to the kernel and set appropriately with src_vni.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
sharathr [Tue, 19 Oct 2021 11:01:50 +0000 (04:01 -0700)]
zebra: Fix for mcast-group update and delete per vni for svd
Ticket: 2698649
Testing Done: precommit and evpn-min
Problem:
When the mcast-group is updated, the changes were being read from the netlink
and populated by zebra, but when kernel sends the delete of fdb delete for the
group, we are deleting the mcast-group that we newly updated. This is because,
currently we blindly reset the mcast-group during fdb delete without checking
for mcast-group associated to the vni.
Fix is to separate add/update and delete mcast-group functions and to check
for mcast-group before resetting during delete.
sharathr [Fri, 8 Oct 2021 14:27:50 +0000 (07:27 -0700)]
zebra: fix for unexpected fdb entry showing up during ifdown/ifup events
Ticket: 2674793
Testing Done: precommit, evpn-min and evpn-smoke
The problem in this case is whenever we are triggering ifdown
followed by ifup of bridge, we see that remote mac entries
are programmed with vlan-1 in the fdb from zebra and never cleaned up.
bridge has vlan_default_pvid 1 which means any port that gets added
will initially have vlan 1 which then gets deleted by ifupdown2 and
the proper vlan gets added.
The problem lies in zebra where we are not cleaning up the remote
macs during vlan change.
Fix is to uninstall the remote macs and then install them
during vlan change.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
When the VLAN-VNI mapping is configured via a map and not using
individual VXLAN interfaces, upon removal of a VNI ensure that the
remote FDB entries are uninstalled correctly.
Signed-off-by: Vivek Venkatraman <vivek@nvidia.com>
Ticket: #2613048
Reviewed By:
Testing Done:
1. Manual verification - logs in the ticket
2. Precommit (user job #171) and evpn-min (user job #170)
Signed-off-by: Stephen Worley <sworley@nvidia.com>
Ticket: 2730328, 2724075
Reviewed By: CCR-11741, CCR-11746
Testing Done: Unit Test
2730328: At high bridge-vids count, VNI devices are not added in FRR if
FRR restarts after loading e/n/i
The issue is the wrt buffer overflow for netlink_recv_msg.
We have defined the kernel recv message buffer in stack which is of size 32768 (32K).
When the configuration is applied without FRR restart things work fine
because the recv message from kernel is well within the limit of 32K.
However with this configuration, when the FRR was restarted I could see that
some recv messages were crossing the 32K limit and hence weren't processed.
Below error logs were seen when frr was restarted with the confuguration.
2021/08/09 05:59:55 ZEBRA: [EC 4043309092] netlink-cmd (NS 0) error: data remnant size 32768
Fix is to increase the buffer size by another 2K
2724075: evpn mh/SVD - some of the remote neighs/macs aren't installed
in kernel post ifdown/ifup bridge
The issue was specific to SVD. During ifdown/ifup of the bridge,
I could see that the access-bd was not associated with the vni and hence
the remote neighs were not getting programmed in the kernel.
Fix is to reference (or associate) vxlan vni to the access-bd when
the vni is reported up. With this fix, I was able to see the remote
neighs getting programmed to the kernel.
Stephen Worley [Fri, 9 Dec 2022 22:23:32 +0000 (17:23 -0500)]
bgpd: SA set labels/num_labels to NULL/0
Static Analysis caught a bug where we could be reading
garbage values for labels/num_lables. Fix that by
ensuring it's set to NULL/0 per loop of the mpath.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
Stephen Worley [Tue, 22 Nov 2022 21:41:54 +0000 (16:41 -0500)]
zebra: ignore zero_mac without VNI deletes
Ignore zebra_mac updates if they do not contain a VNI for vxlan
interface. We don't have anything we can do with them.
'''
==443593== Process terminating with default action of signal 6 (SIGABRT): dumping core
==443593== at 0x4E1156C: __pthread_kill_implementation (in /usr/lib64/libc.so.6)
==443593== by 0x4DC4D15: raise (in /usr/lib64/libc.so.6)
==443593== by 0x49823C7: core_handler (sigevent.c:261)
==443593== by 0x4DC4DBF: ??? (in /usr/lib64/libc.so.6)
==443593== by 0x4E1156B: __pthread_kill_implementation (in /usr/lib64/libc.so.6)
==443593== by 0x4DC4D15: raise (in /usr/lib64/libc.so.6)
==443593== by 0x4D987F2: abort (in /usr/lib64/libc.so.6)
==443593== by 0x49C3064: _zlog_assert_failed (zlog.c:700)
==443593== by 0x4F5E6D: zebra_vxlan_if_vni_find (zebra_vxlan_if.c:661)
==443593== by 0x4EEAC3: zebra_vxlan_check_readd_vtep (zebra_vxlan.c:4244)
==443593== by 0x450967: netlink_macfdb_change (rt_netlink.c:3722)
==443593== by 0x450011: netlink_neigh_change (rt_netlink.c:4458)
'''
Signed-off-by: Stephen Worley <sworley@nvidia.com>
projects / mirror / frr.git / log